CMC 8000 Plus Support Documentation

Wizard CMC 8000 Plus Overview

• Design Examples Cut on a Wizard CMC: Video

• How a Wizard CMC Can Help Your Business: Video

• Wizard CMC 9000 Overview: Video (The CMC 8000 Plus uses a 9000 Board Base)

• Wizard CMC with SwitchBlade Technology Overview Video

Board

• Aborted a Cut and Now it Will not Cut

• Clamps are not Engaging

• CMC Components Labeled: 8000 Plus

• CMC Model Cutting Information: CMC 8000, 9000, Z Series and Eclipse

• Push to Cut Button Does Nothing

Board: Drive Belt Documents

• Drive Belt Position Alignment: All Current CMC Models

• Drive Belt Position Fine-Tune: All Current CMC Models

• Drive Belt Replacement: All Current CMC Models

Board: Emergency Stop Button

• Emergency Stop Button: CMC 8000 Series Containing an Emergency Stop Button

Board: Horizontal Belt: Adjust Horizontal Belt Tension

• Horizontal Belt Tension Adjustment: All Current CMC Models

Board: Maintenance: Recommended Maintenance

• Maintenance Recommended for the CMC: All Current CMC Models

• Maintenance Recommended for the CMC: Video: All Current CMC Models

Cartridges: Blades: Changing the Blade Documents

• Cartridge And Blade Identification: All Current CMC Models

• Change the 45 Degree Blade: All Current CMC Models

• Change the 45 Degree Blade: Video

• Change the 45 Degree Plus Blade: CMC 9000, Z Series and the 8000 Plus

• Change the 90 Degree Blade: CMC 8500eSBT, 9000, Z Series and the 8000 Plus

• Getting Started FrameShop Cartridge Manual: All Current CMC Models

Cartridges: Changing the Cartridges Documents

• Cartridge And Blade Identification: All Current CMC Models

• Change to the 45 Degree Cartridge: All Current CMC Models

• Change to the 45 Plus Degree Cartridge: CMC 9000, Z Series and the 8000 Plus

• Change to the 90 Degree Cartridge: CMC 8500eSBT, 9000, Z Series and the 8000 Plus

• Change to the Deboss Cartridge: All Current CMC Models

• Getting Started FrameShop Cartridge Manual: All Current CMC Models

Cutting Issues

• Cuts are Crooked/Skewed

• Corners are Twisted

• Cuts are off Horizontally

• Matboard Moves Aside when Cutting

• Nothing Happens when you try to Cut

• Openings have Swoops not Correctable by Configurations

ECU Documents

• Could Not Find Compatible Hardware

• ECU Driver Installation: CMC 8500 Series and the 9000

• ECU Driver Installation: FrameShop: CMC 8000 Series, 9000 and the Z Series

• ECU/Driver Pack Types: All Current CMC Models

• ECU Driver Uninstallation: CMC 8000, 9000, Z Series, 8000RC and the 8000 Plus

• ECU Ferrite Attachment Installation: CMC Z Series

• ECU Hardware Installation: CMC 8000, 9000, Z Series, 8000RC and the 8000 Plus

• ECU Turning Off and On Specifics: All Current CMC Models

• No Power Available to the ECU/Driver Pack: All Current CMC Models

• USB HUB for Improved ECU Connection Performance: CMC 8000, 8500 Series and the 9000

Gantry Documents

• Air Valve Assembly Replacement: All Current CMC Models Except the 8500e

• Air Valve Assembly Replacement Video: All Current CMC Models Except the 8500e

• Air Valve Assembly Test Buttons: All Current CMC Models

• Connecting the Gantry Air Lines Video

• Gantry is not Moving Horizontally

• Gantry Replacement: CMC 8000 Series, 9000 and the Z(9000z)

• Gantry Squeaks as the Head Moves Vertically

• Igus Cover Adjustment: CMC 8000 and 8500 Series

• Vertical Belt Pulley Lubrication Instructions: All Current CMC Models

• Vertical Belt Pulley Replacement Instructions: All Current CMC Models

• Vertical Belt Tension Adjustment: CMC 9000, Z Series and the 8000 Plus

Getting Started

• CMC Setup Checklist: All Current CMC Models

• Getting Started Manual CMC 8000 Plus

Head Documents

• Align the Head: All Current CMC Models

• Align the Head Video

• Blade Cartridge is not Plunging

• Blade Depth Dial Calibration: All but CMC Z1

• Blade Depth Dial Calibration Video

• Blade not Cutting Through the Matboard

• Cannot Get Matboard under the Footblock (8000 Series)

• Cuts Stop/Head Drops in the Middle of Cutting

• Cutting a Dense Layer: VPO: CMC 9000, Z Series and the 8000 Plus

• Cutting an Extra Dense Layer with the 90° Cartridge: VPO: CMC 9000, Z Series and the 8000 Plus

• Cutting a Typical Matboard: VPO: CMC 9000, Z Series and the 8000 Plus

• Floating Foot Screw Adjustment: CMC 8000

• Footblock Cleaning and Lubrication: All Current CMC Models

• Footblock is not Rotating or not Rotating Correctly (Head Z-Axis)

• Footblock Leaving Indents on the Matboard

• Footblock Replacement Instructions: All Current CMC Models

• Head Assembly Power Cable Strain Relief: CMC 8000, 9000 and Z Series

• Head is not Lifting from Mat (8000 Series)

• Head Replacement: CMC 8000 Series, 9000 and Z(9000z)

• Head Retainer Ring Replacement Video

• Head Wheel Adjustment: All Current CMC Models Except the Z1

• Head Wheel Adjustment Video: All Current CMC Models Except the Z1

• Measuring the Blade Depth: All Current CMC Models Except the Z1

• Variable Pressure Optimization (VPO) Documents: CMC 9000, Z Series and the 8000 Plus

Parts Return Packaging Documentation

• CMC Shipping Box Assembly: All Current CMC Models

• Packaging Gantry and Head to Ship Back to Wizard: CMC 8000, 9000 and Z Series

• Repackaging Instructions for Customers Moving the CMC: All Current CMC Models

• Shipping Weight and Dimensions

• Upgrade/Termination Hardware Return Instructions

CMC Stand Documents

• CMC Floor Stand Assembly | Step-by-Step Guide

• CMC With Board Mounting Bracket

• Consolidated Floor Stand 2024

• Fixed Wall Mount Instructions: All Current CMC Models

• Floor Stand Assembly Instructions: All Current CMC Models

• Retractable Wall Mount (RWM) Operations Manual: CMC 8500, 9000 and Z Series

• Wizard Space-Saver CMC Overview Video

Hardware Support Information Quick Links

• Wizard Knowledge Base

• Hardware Support Information: All CMC Models

• Troubleshooting Hardware