Cartridges Involved
This Configuration element involves the following Cartridges.
Note: Not all cartridges are available for all CMC models.
Deboss Wide Configurations
Info |
---|
|
Expand | ||
---|---|---|
| ||
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
Select the Deboss Wide Cartridge Type
Select the Deboss Tab on the Configurations screen.
Select the Wide-Blue cartridge from the Cartridge dropdown control.
Select the Area of Concern for Wide Deboss Below:
Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.Deboss Wide Configurations |
---|
Contents: |
Problem:
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Non-Blade Tool line is applied too far Left:
Increase the Horizontal Adjustment.
Decrease the Horizontal Adjustment.
See Horizontal Adjustment for additional information.
Expand | ||
---|---|---|
| ||
The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges. If the Non-Blade Tool line is applied Too Far Left, Increase the Horizontal Adjustment. If the Non-Blade Tool line is applied Too Far Right, Decrease the Horizontal Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Problem:
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
|
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Non-Blade Tool line is applied too far Up:
Decrease the Vertical Adjustment.
Non-Blade Tool line is applied too far Down:
Increase the Vertical Adjustment.
See Vertical Adjustment for additional information.
Expand | ||
---|---|---|
| ||
The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges. If the Non-Blade Tool line is applied Too Far Up, Decrease the Vertical Adjustment. If the Non-Blade Tool line is applied Too Far Down, Increase the Vertical Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Problem:
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Opening cuts too Large:
Decrease the Opening Adjustment.
Opening cuts too Small:
Increase the Opening Adjustment.
See Opening Adjustment for additional information.
Expand | ||
---|---|---|
| ||
The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges. If the Opening is cut Too Large, Decrease the Opening Adjustment. If the Opening is cut Too Small, Increase the Opening Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Problem:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Non-Blade Tool is too Deep:
Decrease the Depth Setting.
Non-Blade Tool is too Shallow:
Increase the Depth Setting.
See Depth Setting for additional information.
title | Depth Setting Definition |
---|
Problem:
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Non-Blade Tool is Tearing in the Corners of the segments:
Increase the Corner Pause.
Non-Blade Tool is Pausing Too Long in the Corners of the segments:
Decrease the Corner Pause.
See Corner Pause for additional information.
title | Corner Pause Definition |
---|
The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause.
The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.
Problem:
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Decrease the Overshoot.
See Overshoot for additional information.
Expand | ||
---|---|---|
| ||
The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl). This is similar to the Overcut used with the Blade cartridges. If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot. If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Problem:
This is viewed from the front of the mat.
Resolution:
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Increase the Overshoot.
See Overshoot for additional information.
Expand | ||
---|---|---|
| ||
The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl). This is similar to the Overcut used with the Blade cartridges. If the Overshoot is applied too Long, Decrease the Overshoot. If the Overshoot is applied too Short, Increase the Overshoot. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
panelIconId | atlassian-note |
---|---|
panelIcon | :note: |
bgColor | #B3F5FF |
Non-Blade Tool leaves a Dot where it plunges:
Select Unplunge.
Non-Blade Tool takes Too Long to apply:
Select Plunge.
See Plunge for additional information.
Problem:
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
|
Resolution:
Deboss Wide Definition | |||
---|---|---|---|
|
The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.
The Non-Blade Tool takes Too Long to apply, select Plunge.
Troubleshooting Button
Info |
---|
|
Expand | ||
---|---|---|
| ||
The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. |
|
|