Versions Compared

Old Version 38

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Image Removed

Deboss Wide Configurations

Info

  • The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

  • This is viewed from the front of the mat.

Expand
titleCartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Image Removed

Select the Deboss Wide Cartridge Type

  • Select the Deboss Tab on the Configurations screen.  

  • Select the Wide-Blue cartridge from the Cartridge dropdown control.

Tip

  • Deboss Wide

Image Removed

Select the Area of Concern for Wide Deboss Below:

  • Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.

Deboss-Wide is Applied to the Wrong Place Horizontally

Problem:

The Deboss-Wide is applied to thewrong place Horizontally.

  • This is viewed from the front of the mat.

    • Resolution:

    If the Non-BladeTool line is applied too far Left Horizontally, Increase the Horizontal Adjustment.If the Non-BladeTool line is applied too far Right Horizontally, Decrease the Horizontal Adjustment.

  • See Horizontal Adjustment for additional information.

    • Expand
    titleHorizontal Adjustment Definition

    The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

    If the Non-Blade Tool line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

    If the Non-Blade Tool line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

    Image Removed

    Deboss-Wide is Applied to the Wrong Place Vertically 

    Problem:

    • The Deboss-Wide is applied to the wrong place Vertically.

    • This is viewed from the front of the mat.

    Resolution:

    If the Non-BladeTool line is applied too far Up Vertically, Decrease the Vertical Adjustment.If the Non-BladeTool line is applied too far Down Vertically, Increase the Vertical Adjustment.

  • See Vertical Adjustment for additional information.

    • Expand
    titleVertical Adjustment Definition

    The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

    If the Non-Blade Tool line is applied Too Far Up Vertically, Decrease the Vertical Adjustment.

    If the Non-Blade Tool line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

    Image Removed

    Deboss-Wide is the Wrong Size

    Problem:

    • The Deboss-Wide is the Wrong Size.

    • This is viewed from the front of the mat.

    Resolution:

    Expand
    titleOpening Adjustment Definition

    The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

    If the Opening is cut Too Large, Decrease the Opening Adjustment.

    If the Opening is cut Too Small, Increase the Opening Adjustment.

    Image Removed

    Deboss-Wide Applied at the Wrong Depth

    Problem:

    • The Deboss-Wide is applied at the Wrong Depth.

    • This is viewed from the front of the mat.

    Resolution:

    The Non-BladeTool is too Deep, Decrease the Depth Setting.The Non-BladeTool is too Shallow, Increase the Depth Setting.

  • See Depth Setting for additional information.

    • Expand
    titleDepth Setting Definition
    The Depth Setting controls the Blade Depth for the Non-BladeTools in the Configurations.If the Non-BladeTool is too Deep, Decrease the Depth Setting.If the Non-BladeTool is too Shallow, Increase the Depth Setting.Image Removed

    Deboss-Wide Cartridge Tears the Mat 

    Problem:

    • Deboss-Wide Cartridge Tears the Mat.

    • This is viewed from the front of the mat.

    Resolution:

    The Non-BladeTool is Tearing in the Corners of the segments, Increase the Corner Pause. The Non-BladeTool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

  • See Corner Pause for additional information.

    • Expand
    titleCorner Pause Definition
    The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Toolsbetween segments.

    The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

    The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.  

    Image Removed

    Deboss-Wide Lines are too Long

    Problem:

    The Deboss-WideLines are Too Long.

  • This is viewed from the front of the mat.

    • Resolution:

    • If the Overshoot is applied too Long, Decrease the Overshoot.

    • See Overshoot for additional information.

    Expand
    titleOvershoot Definition

    The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

    This is similar to the Overcut used with the Blade cartridges.

    If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

    If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

    Image Removed

    Deboss-Wide Lines are too Short 

    Problem:

    The Deboss-WideLines are Too Short.

  • This is viewed from the front of the mat.

    • Resolution:

    • If the Overshoot is applied too Long, Decrease the Overshoot.

    • If the Overshoot is applied too Short, Increase the Overshoot.

    • See Overshoot for additional information.

    Expand
    titleOvershoot Definition

    The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

    This is similar to the Overcut used with the Blade cartridges.

    If the Overshoot is applied too Long, Decrease the Overshoot.

    If the Overshoot is applied too Short, Increase the Overshoot.

    Image Removed

    Deboss-Wide Set to Plunge Between Segments

    Problem:

    • The Deboss-Wide Set to Plunge Between Segments.

    • This is viewed from the front of the mat.

    Resolution:

    The Non-BladeTool leaves a Dot where it plunges, select Unplunge.The Non-BladeTool takes Too Long to apply, select Plunge.

  • See Plunge for additional information.

    • Expand
    titlePlunge Definition

    The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

    The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

    The Non-Blade Tool takes Too Long to apply, select Plunge.

    Image Removed

    Troubleshooting Button 

    Info
    Expand
    titleTroubleshooting Button Definition

    The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

    Image Removed

    Deboss Wide Configurations

    Contents:

    Deboss Wide Definition

    Expand
    titleDeboss Wide Definition

    The Deboss Wide Blue cartridge stylus presses onto the surface of the matboard to create a subtle design with a Wide line.

    There are three Deboss stylus sizes: Wide, Medium, Thin.

    In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

    Image AddedImage Added

    See: Add Deboss Opening Function