Cartridges Involved
This Configuration element involves the following Cartridges.
Note: Not all cartridges are available for all CMC models.
Deboss Wide Configurations
Info |
---|
|
Expand | ||
---|---|---|
| ||
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
Select the Deboss Wide Cartridge Type
Select the Deboss Tab on the Configurations screen.
Select the Wide-Blue cartridge from the Cartridge dropdown control.
Tip |
---|
|
Select the Area of Concern for Wide Deboss Below:
Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.
Deboss Wide Configurations |
---|
Contents: |
Resolution:
If the Non-BladeTool line is applied too far Left Horizontally, Increase the Horizontal Adjustment.If the Non-BladeTool line is applied too far Right Horizontally, Decrease the Horizontal Adjustment.See Horizontal Adjustment for additional information.
Expand | ||
---|---|---|
| ||
The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges. If the Non-Blade Tool line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment. If the Non-Blade Tool line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment. |
Resolution:
If the Non-BladeTool line is applied too far Up Vertically, Decrease the Vertical Adjustment.If the Non-BladeTool lineSee Vertical Adjustment for additional information.
title | Vertical Adjustment Definition |
---|
If the Non-Blade Tool line is applied Too Far Up Vertically, Decrease the Vertical Adjustment.
If the Non-Blade Tool line is applied Too Far Down Vertically, Increase the Vertical Adjustment.
Deboss-Wide is the Wrong Size
Problem:
The Deboss-Wide is theResolution:
If the Opening is cut too Large, Decrease the Opening Adjustment.
If the Opening is cut too Small, Increase the Opening Adjustment.
See Opening Adjustment for additional information.
The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.
If the Opening is cut Too Large, Decrease the Opening Adjustment.
If the Opening is cut Too Small, Increase the Opening Adjustment.
Problem:
Resolution:
The Non-BladeTool is too Deep, Decrease the Depth Setting.The Non-BladeTool is too Shallow, Increase the Depth Setting.See Depth Setting for additional information.
title | Depth Setting Definition |
---|
Problem:
Resolution:
The Non-BladeTool is Tearing in the Corners of the segments, Increase the Corner Pause. The Non-BladeTool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.See Corner Pause for additional information.
title | Corner Pause Definition |
---|
The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause.
The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.
Resolution:
If the Overshoot is appliedSee Overshoot for additional information.
title | Overshoot Definition |
---|
The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).
This is similar to the Overcut used with the Blade cartridges.
If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.
If the Overshoot of the Non-Blade Tool is applied TooProblem:
The Deboss-WideLines are Too Short.Resolution:
Deboss Wide Definition | |||
---|---|---|---|
|
Deboss-Wide Set to Plunge Between Segments
Problem:
The Deboss-Wide Set to Plunge Between Segments.
Resolution:
The Non-BladeTool leaves a Dot where it plunges, select Unplunge.The Non-BladeTool takes Too Long to apply, select Plunge.See Plunge for additional information.
Expand | ||
---|---|---|
| ||
The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool. The Non-Blade Tool leaves a Dot where it plunges, select Unplunge. The Non-Blade Tool takes Too Long to apply, select Plunge. |
Troubleshooting Button
Info |
---|
|
Expand | ||
---|---|---|
| ||
The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. |
|
This is similar to the Overcut used with the Blade cartridges.
If the Overshoot is applied too Long, Decrease the Overshoot.
If the Overshoot is applied too Short, Increase the Overshoot.
|