Versions Compared

Old Version 13

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Creating a Multi-Layered Oval Inset

Info

  • This lesson shows how to make a Multi-Layer Oval Inset mat.

Image Removed

  • .

Panel
panelIconId1f9d9-200d-2640-fe0f
panelIcon:woman_mage:
panelIconText🧙‍♀️
bgColor#FFEBE6
Image Added

Design in FrameShop, Bring into

PathTrace

Trace

  • First we need to make sure we are designing the layers in the correct order for these instructions.

  • On the FrameShop Main Page, click Admin and stay on the Defaults tab.

  • Under Layer Direction select Bottom Up if it is not already set to that.

  • Click Save and return to the Main Page.

    • You can change this back to the original setting later if desired.

Panel
panelIconIdatlassian-note1f9d9-200d-2640-fe0f
panelIcon:note:bgColor#B3F5FFwoman_mage:
panelIconText🧙‍♀️
bgColor#FFEBE6

  • Layer Direction: Bottom Up is the preferred direction.

    • When you Offset an object to create another layer, that new layer will be the Top layer.

  • Layer Direction: Top Down is not recommended.

    • When you Offset an object to create another layer, that new layer will be the Bottom layer, even though it is larger than the original object.

2LayerLetterMatDefaultDirection800.pngImage Added

  • Place an 8.75 x 11.75” #102 Oval Template with two Layers on the FrameShop Design Editor. 

  • Bring in two small ovals that are 3x5.

  • Edit the small ovals and make them four layers.

    • Width of the Inner Reveal is how much of the Inner Mat shows (i.e., .25).

    • Width of the Middle Reveal is the width of the Bridge between the two objects (i.e., .5).

    • Outer Reveal is the Inner Mat of the Bridge on the large object side (i.e., .25).

Insert excerpt
Templates Definition
Templates Definition
nameTemplates Definition
#B3F5FF

Bring Design into Trace

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor

Image Removed
Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • The View from Back toggle toggles between viewing the design from the Front or from the Back of the mat.

Image Removed
Image Added
The Breaktool is used to Bisect the Selected Segments at the points where they Intersect in the Trace software.

The Break All Intersections function bisect ALL Segments in the design at the points where they intersect with another segment in the Trace software.

 

Image Removed

Break All Intersections

atlassian-note
Info

  • Because of the complexity of this design, it may be easier to Break All of the Intersections and reconnect the desired Arcs.

Panel
panelIconId

panelIcon:note:
bgColor#B3F5FF
Expand
titleArc Definition

The Arc Tool tool function allows you to draw a three-point mathematically defined curve in the Trace software.

The Arc has three points: the Initial Position and the Terminating Position (which are called "anchors") and one separate Middle point (which is called a "handle") which can be moved to change the shape of the Arc.

Expand
titleSpline Definition

The Curve function allows you to draw a four-point mathematically defined Bezier/Spline Curve in the Trace software.

The Bezier/Spline Curve is defined by four points: the Initial Position and the Terminating Position (which are called "Anchors") and two separate Middle Points (which are called "Handles"), which can be moved to alter the shape.

Expand
titleBreak Definition
Insert excerpt
Break All Intersections Definition
Break All Intersections Definition
nameBreak All Intersections Definition
Image Added
panelIcon

  • The design has been Broken and consists of many tiny Arcs.

  • Zoom In/Out as needed to select the smaller Arcs.

The Breaktool is used to Bisect the Selected Segments at the points where they Intersect in the Trace software.

The Break All Intersections function bisect ALL Segments in the design at the points where they intersect with another segment in the Trace software.

Join Segments / Close Circuit

Panel
panelIconIdatlassian-info

:info:
bgColor#B3F5FF
Expand
titleBreak Definition
Expand
titleArc Definition

The Arc Tool tool function allows you to draw a three-point mathematically defined curve in the Trace software.

The Arc has three points: the Initial Position and the Terminating Position (which are called "anchors") and one separate Middle point (which is called a "handle") which can be moved to change the shape of the Arc.

Expand
titleSpline Definition

The Curve function allows you to draw a four-point mathematically defined Bezier/Spline Curve in the Trace software.

The Bezier/Spline Curve is defined by four points: the Initial Position and the Terminating Position (which are called "Anchors") and two separate Middle Points (which are called "Handles"), which can be moved to alter the shape.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Holding down the CTRL key, click on each segment that is forming the Inner Layer of the Lower Oval in the order they are sitting.

Image Removed PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FFImage Added

  • When the Oval is completely selected, click Join.

Expandtitle
Insert excerpt
Join Tool Definition
Join Tool Definition

The Join button will connect the selected segments together as one object in Trace. 

The Auto Join Segments button will automatically join adjacent segments together in Trace.

Image Removed Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF
nameJoin Tool Definition

Image Added

  • The Oval is now a connected singular object.

Expand
titleJoin Definition

The Join button will connect the selected segments together as one object in Trace. 

The Auto Join Segments button will automatically join adjacent segments together in Trace.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Connect the Arcs making up the next layer of the Bottom Oval in the same manner.

Expand
titleArc Definition

The Arc Tool tool function allows you to draw a three-point mathematically defined curve in the Trace software.

The Arc has three points: the Initial Position and the Terminating Position (which are called "anchors") and one separate Middle point (which is called a "handle") which can be moved to change the shape of the Arc.

Expand
titleSpline Definition

The Curve function allows you to draw a four-point mathematically defined Bezier/Spline Curve in the Trace software.

The Bezier/Spline Curve is defined by four points: the Initial Position and the Terminating Position (which are called "Anchors") and two separate Middle Points (which are called "Handles"), which can be moved to alter the shape.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Connect the Arcs for the Bottom Layer of the Top Oval.

    • Notice that this will use Arcs from the original outer layer of the Bottom Oval, to form part of this Top Oval.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Connect the Arcs for the next layer of the Top Oval in the same manner.

Image Removed PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FFImage Added

  • Connect the Inner Layer of the Large Oval.

    • Notice that this will use Arcs from the original Outer Layer of the Smaller Ovals, to form part of this Large Oval.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Connect the Arcs for the next layer of the Large Oval in the same manner.

Image Removed PanelpanelIconIdatlassian-infopanelIcon:info:bgColor#B3F5FFImage Added

  • The Ovals are now connected.

Info

  • NOTE: It is not necessary to delete the leftover Arcs.

    • Because the spare Arcs are not connected, the user can simply Trace the desired objects.

    • The leftover Arcs are deleted here for illustration purposes.

Expand
titleArc Definition

The Arc Tool tool function allows you to draw a three-point mathematically defined curve in the Trace software.

The Arc has three points: the Initial Position and the Terminating Position (which are called "anchors") and one separate Middle point (which is called a "handle") which can be moved to change the shape of the Arc.

Expand
titleSpline Definition

The Curve function allows you to draw a four-point mathematically defined Bezier/Spline Curve in the Trace software.

The Bezier/Spline Curve is defined by four points: the Initial Position and the Terminating Position (which are called "Anchors") and two separate Middle Points (which are called "Handles"), which can be moved to alter the shape.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image RemovedImage Added
PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FFClick Edit > Convert Arc to Splines to convert the Arcs into Bezier Splines. Splines can be Tangified
in Trace

  • .

 

The Tangify function will smooth the connection between the Selected Arc Circuits that are below the specified Angle in the Tangify field to provide a smoother cutting transition between the arcs. 

The Tangify All Circuits will smooth the connection between All of the ArcCircuits that are below the specified Angle
to provide a smoother cutting transition between the arcs. 

Tangify/Convert to Splines

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Click Edit > Tangify all Circuits.

  • Click Edit > Convert Arcs to Splines.

Expand
titleArc Definition

The Arc Tool tool function allows you to draw a three-point mathematically defined curve in the Trace software.

The Arc has three points: the Initial Position and the Terminating Position (which are called "anchors") and one separate Middle point (which is called a "handle") which can be moved to change the shape of the Arc.

Expand
titleSpline Definition

The Curve function allows you to draw a four-point mathematically defined Bezier/Spline Curve in the Trace software.

The Bezier/Spline Curve is defined by four points: the Initial Position and the Terminating Position (which are called "Anchors") and two separate Middle Points (which are called "Handles"), which can be moved to alter the shape.

Expand
titleConvert Arcs to Splines Definition
Expand
titleTangify Definition
Image RemovedImage Removed

Remove Layers

  • ; the default is six degrees.

Insert excerpt
Convert Arc to Splines
Convert Arc to Splines
nameConvert Art to Splines Definition
Insert excerpt
Tangify All Circuits Definition
Tangify All Circuits Definition
nameTangify All Circuits Definition
Image AddedImage Added
Image Removed

Trace the Design

  • Go to the Set Bevels Tab.

  • Select and delete

two

  • Two of the layers by clicking Remove.

  • The two layers we will trace this design on will remain.

Trace, Save, Cut

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Trace, Save and Cut the design.

Expand
titleBevel Type Definition

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

  • Click on the Top Layer.

  • Hold down the Ctrl key and click on the each of the outside openings.

  • Select the desired Bevel Type then click Set.

  • The outside openings of this design turn the color of the Bevel Type selected.

OvalTraceTop70800.pngImage Added

  • Click on the Bottom Layer.

  • Hold down the Ctrl key and click on the each of the inside openings.

  • Select the desired Bevel Type then click Set.

  • The inside openings of this design turn the color of the Bevel Type selected.

  • The design is now completely traced.

Insert excerpt
Traced
Traced
nameTraced Definition
OvalTraceBottom70800.pngImage Added

Save and Cut

  • Save and Cut the design.

Image Added
Image Removed

Comparison

You can see how much we changed the design when you compare it to the original version.

Image Removed

Image AddedImage Added

Default Settings