45 Degree Normal Bevel Drop Configurations

The 45° Normal Bevel Drop is created by cutting into the fallout surface with the blade angled at 45°, thereby slanting the bevel away from the fallout surface. The matboard core is visible from the front.

The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer.

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Select Normal Drop or Normal Drop-Front of Mat from the Current Bevel Type dropdown control to edit this configuration.

The 45° Normal Bevel Open V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement a specified distance apart. Both the matboard core and the lower layer matboard are visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise: Normal Bevel Drop*.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise: Normal Bevel Opening.

*The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer.

Select Normal Drop or Normal Drop-Front of Mat from the Current Bevel Type dropdown control to edit the interior cut configuration.

Select Normal Bevel or Normal Bevel-Front of Mat from the Current Bevel Type dropdown control to edit the exterior cut configuration.

See: 45 Degree Normal Bevel Drop Configurations

See: 45 Degree Normal Bevel Opening Configurations

Cutting from the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview.

• On the Configurations screen the Current Bevel Type dropdown control will display the bevel types in this manner:

  • Cut from the Back bevel type names will be displayed with no further label; i.e., Normal Bevel.

  • Cut from the Front bevel type names will be displayed with a Front label; i.e., Normal Bevel-Front of Mat.

  • V-Grooves have their own selection on the list.

If you are cutting an element that must be applied to the front of the mat, such as a V-Groove or Pen design, any openings on that layer will also cut from the front and use the Front of Mat configuration item; i.e., Normal Bevel - Front of Mat.

So if you are having problems with a Normal Bevel cut on the same layer as a V-Groove, make sure you select Normal Bevel-Front of Mat to edit the configurations for that opening.   

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Depth Bias is used to calculate the proper Blade Depth when the SKU selected for the matboard contains the Matboard Thickness.

If the Blade Depth is cut Too Deep, Decrease the Depth Bias.

If the Blade Depth is cut Too Shallow, Increase the Depth Bias.

The formula is: [(Default Depth) - 10]

For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.

See: Depth Bias

The Plunge Count controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

See: Plunge Count

The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup.

If the Exterior Backup is cut Too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut Too Short, Increase the Exterior Backup.

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

See: Exterior Backup for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup.

If the Exterior Backup is cut Too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut Too Short, Increase the Exterior Backup.

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

See: Exterior Backup for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Backup is cut Too Long, Decrease the Interior Backup.

If the Interior Backup is cut Too Short, Increase the Interior Backup.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration.

See: Interior Backup for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Backup is cut Too Long, Decrease the Interior Backup.

If the Interior Backup is cut Too Short, Increase the Interior Backup.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration.

See: Interior Backup for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

See: Opening Adjustment for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

A Swoop in a Drop is where the corners Curve Inward toward the drop.

If the Drop has a Swoop, Increase the Rotation.

The Rotation controls for Swoops and Flares in Openings.

See: Rotation Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

A Flare in a Drop is where the corners Curve Away from the Drop.

If the Drop has a Flare, Decrease the Rotation.

See: Rotation Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

A Bump in an Oval Drop is a Lump of material left behind where the cut started and ended.

If the Oval Drop has a Bump, Increase the Oval Rotation.

See: Oval Rotation Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval.

If the Oval Drop has a Feather, Decrease the Oval Rotation.

See: Oval Rotation Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval.

If the Oval Drop has a Feather, Decrease the Oval Rotation.

See: Oval Rotation Configurations

A Bump in an Oval Drop is a Lump of material left behind where the cut started and ended.

If the Oval Drop has a Bump, Increase the Oval Rotation.

See: Oval Rotation Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.