Page Comparison

• The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Select desired Cartridge Tab. 

Select the desired Deboss Cartridge Size from Current Bevel Type.

Edit the desired Configuration field.

Image Removed

• Non-Blade Tool line is applied too far Left:

  • Increase the Horizontal Adjustment.

• Non-Blade Tool line is applied too far Right:

  • Decrease the Horizontal Adjustment.

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Left, Increase the Horizontal Adjustment.

If the Non-Blade Tool line is applied Too Far Right, Decrease the Horizontal Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide is applied to the wrong place Vertically.

• Non-Blade Tool line is applied too far Up:

  • Decrease the Vertical Adjustment.

• Non-Blade Tool line is applied too far Down:

  • Increase the Vertical Adjustment.

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Up, Decrease the Vertical Adjustment.

If the Non-Blade Tool line is applied Too Far Down, Increase the Vertical Adjustment.

• Opening cuts too Large:

  • Decrease the Opening Adjustment.

• Opening cuts too Small:

  • Increase the Opening Adjustment.

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Non-Blade Tool is too Deep:

  • Decrease the Depth Setting.

• Non-Blade Tool is too Shallow:

  • Increase the Depth Setting.

• Deboss-Wide Cartridge Tears the Mat.

• Non-Blade Tool is Tearing in the Corners of the segments:

  • Increase the Corner Pause. 

• Non-Blade Tool is Pausing Too Long in the Corners of the segments:

  • Decrease the Corner Pause. 

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Increase the Overshoot.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide Set to Plunge Between Segments.

• Non-Blade Tool leaves a Dot where it plunges:

  • Select Unplunge.

• Non-Blade Tool takes Too Long to apply:

  • Select Plunge.

• Use the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.