Versions Compared

Old Version 15

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Line Design Details

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Click on a Line to see the specific details about it. 

Line Design Details

  • Click on a Line to see the specific details about it. 

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information:

  • See Line Tool for drawing a Line.

Expand
titleLine Tool Definition

The Line tool in Trace will draw a Two-Point Line. 

The Line is defined by two points:

the

Initial Position (called an Anchor) and the Terminating Position (

which are called “anchors”

called an Anchor).

After it is drawn, a third point in the Center

is

will be displayed, which can be moved to alter the

Line panelIconIdatlassian-

line into an Arc.

Image Added
Image Modified
Panel
Info
panelIcon:info:bgColor#B3F5FF

  • The Design Details section displays information about the selected line.

Image Modified

Design Line Details

Start X and Start Y

PanelpanelIconIdatlassian-info

panelIcon:info:bgColor#B3F5FF

  • Displays the Start X/Y Coordinates of the object’s start point when drawn.

    • If you clicked on the upper left and drew by dragging to the lower right, that would make the start point the upper left corner. 

Expand
titleX Position Definition

The

 X

 X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Image Added
Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image Added
Image Modified

Mid X and Mid Y 

PanelpanelIconId

atlassian-
Info
panelIcon:info:bgColor#B3F5FF

  • The Middle Point X and Y Coordinates.

Expand
titleX Position Definition

The

 X

 X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Image Added

 

Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image Added

 

Image Modified

End X and End Y 

PanelpanelIconIdatlassian-
Info
panelIcon:info:bgColor#B3F5FF

  • The End Point X and Y Coordinates.

Expand
titleX Position Definition

The

 X

 X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Image Added
Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image Added
Image Modified

Angle 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • This displays the Angle, in degrees, of the Line.

  • The Angle is the space, in degrees, between a given line and an unseen horizontal line intersecting its end point. 

Image Modified

Length 

PanelpanelIconIdatlassian-infopanelIcon:info:bgColor#B3F5FF

  • Displays the Length of the Line in the current dimensions.

Image Modified

Bevel Type 

Panel
panelIconId
atlassian-info
1f9d9-200d-2642-fe0f
panelIcon:
info:Displays the Bevel Type if the current line is 
man_mage:
panelIconText🧙‍♂️
bgColor
#B3F5FF
#FFFAE6
Expand
titleBevel Type Definition

The Bevel Type

is the Angle that

refers to the angle at which the blade cuts

on

the

Matboard/Fallout

surface of the matboard when it

is not cut at a 90° Right Angle.

deviates from the 90° right angle cut.

Image Added
Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Added

See: Tracing the Design

Image Modified

Layer 

Panel
panelIconId
atlassian-info
1f9d9-200d-2642-fe0f
panelIcon:
infoDisplays the Layer numberthis line is assigned to if it is Traced
man_mage:
panelIconText🧙‍♂️
bgColor
#B3F5FF
#FFFAE6
Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Added

See: Tracing the Design

Image Modified