Page Comparison

...

If the Vinyl line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.
If the Vinyl line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Vinyl is Cut in the Wrong Place Horizontally

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Horizontal Adjustment/wiki/spaces/FrameShop8x/pages/1942511519for placement adjustment of the non-blade Tools.
See Horizontal Home which defines the global Horizontal placement of objects cut with the Blade Cartridges.
See Horizontal Home on the Troubleshooting Utility to adjust the bladed cartridges.

Expand

title	Vinyl Horizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontalplacement of objects applied with the Vinyl Cartridges.

If the Vinyl line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

If the Vinyl line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

See: Horizontal Adjustment for Vinyl.

Expand

title	How to Adjust the Horizontal Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

panelIcon

If the Vinyl line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment.
If the Vinyl line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

Vinyl is Cut in the Wrong Place Vertically
Panel
panelIconId	atlassian-note

	:note:
bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Vertical Adjustment/wiki/spaces/FrameShop8x/pages/1942511519for placement adjustment of the non-blade Tools.
See Vertical Home which defines the global Vertical placement of objects cut with the Blade Cartridges.
See Vertical Home on the Troubleshooting Utility to adjust the bladed cartridges.

Expand

title	Vinyl Vertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Vinyl Cartridges.

If the Vinyl line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment.

If the Vinyl line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

See: Vertical Adjustment for Vinyl.

Expand

title	How to Adjust the Vertical Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

atlassian-note

If the Vinyl is cut Too Large, Decrease the Opening Adjustment.
If the Vinyl is cut Too Small, Increase the Opening Adjustment.

Vinyl is Cut the Wrong Size
Panel
panelIconId

panelIcon	:note:
bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Opening Adjustment for information on adjusting the object’s size.
See Troubleshooting Utility for information on adjusting the object’s size.

Expand

title	Vinyl Opening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Vinyl is cut Too Large, Decrease the Opening Adjustment.

If the Vinyl is cut Too Small, Increase the Opening Adjustment.

See: Opening Adjustment for Vinyls.

Expand

title	How to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

:note:

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.
If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

Vinyl Cut at the Wrong Depth
Panel
panelIconId	atlassian-note
panelIcon

bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Depth Setting for information on adjusting the Depth of the Non-Blade Tool.

Expand

title	Vinyl Depth Setting Definition

The Depth Setting controls the Blade Depth for theNon-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

See: Depth Setting for Vinyl.

atlassian-note

The Non-Blade Tool Tears the Corners, Increase the Corner Pause.
The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause.

Vinyl Cartridge Tears the Mat
Panel
panelIconId

panelIcon	:note:
bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Corner Pause for information on adjusting the Pause of the Non-Blade Tool in the corners.

Expand

title	Vinyl Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool Tears the Corners, Increase the Corner Pause.

The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause.

See: Corner Pause for Vinyl

Vinyl Lines are too Long

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If

Panel

panelIconId	atlassian-note1f9d9-200d-2642-fe0f
panelIcon	:noteman_mage:
panelIconText	🧙‍♂️
bgColor	#B3F5FF

#FFFAE6

For Additional Information: See Overshoot for information on adjusting the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot in the corners.

Expand

title	Vinyl Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

See: Overshoot for Vinyl.

Expand

title	How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Vinyl Lines are too Short

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

If

Panel

panelIconId	atlassian-note1f9d9-200d-2642-fe0f
panelIcon	:note:man_mage:
panelIconText	🧙‍♂️
bgColor	#B3F5FF

#FFFAE6

For Additional Information: See Overshoot for information on adjusting the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot in the corners.

Expand

title	Vinyl Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

See: Overshoot for Vinyl.

Expand

title	How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.
The Non-Blade Tool takes Too Long to apply, select Plunge.

Vinyl Set to Plunge Between Segments

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Plunge (Tool Specific) for information on adjusting the Plunging of the Non-Blade Tool in the corners.

Expand

title	Vinyl Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

See: Plunge for Vinyl.

info

Troubleshooting Button

Select this topic to see information on the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Troubleshooting Utility.
See Oval Rotation for adjusting for a Feather or a Bump in an Oval.
See Circle/Oval Rotation Utility to adjust for a Feather or Bump in an Oval.
See Rotation for adjusting for a Swoop or Flare in a Non-Oval.
See Horizontal Home which defines the global Horizontal placement of objects cut with the Blade Cartridges.
See Vertical Home which defines the global Vertical placement of objects cut with the Blade Cartridges.
See Opening Adjustment for information on adjusting the object’s size.

Expand

title	Troubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Versions Compared

Old Version 44

New Version 45

Key

Vinyl is Cut in the Wrong Place Horizontally

Vinyl is Cut in the Wrong Place Vertically

Vinyl is Cut the Wrong Size

Vinyl Cut at the Wrong Depth

Vinyl Cartridge Tears the Mat

Vinyl Lines are too Long

Vinyl Lines are too Short

Vinyl Set to Plunge Between Segments

Troubleshooting Button