...
Deboss-Wide is Applied to the Wrong Place Horizontally | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | | |||||||
|
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Horizontal Adjustment defines the global Horizontalplacement of objects applied with the Deboss Cartridges. If the Deboss line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment. If the Deboss line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Deboss-Wide is Applied to the Wrong Place Vertically | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | ||||||||
panelIconId | atlassian-note | |||||||
:note: | ||||||||
bgColor | #B3F5FF |
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Vertical Adjustment defines the global Vertical placement of objects applied with the Deboss Cartridges. If the Deboss line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment. If the Deboss line is applied Too Far Down Vertically, Increase the Vertical Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Deboss-Wide is the Wrong Size | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | panelIconId | atlassian-note|||||||
panelIcon | :note: | |||||||
bgColor | #B3F5FF |
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges. If the Deboss is Too Large, Decrease the Opening Adjustment. If the Deboss is Too Small, Increase the Opening Adjustment. |
Expand | ||
---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Deboss-Wide Applied at the Wrong Depth | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | ||||||||
panelIconId | atlassian-note | panelIcon | :note:||||||
bgColor | #B3F5FF |
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Depth Setting controls the Blade Depth for theNon-Blade Tools in the Configurations. If the Non-Blade Tool is too Deep, Decrease the Depth Setting. If the Non-Blade Tool is too Shallow, Increase the Depth Setting. See: Depth Setting for Deboss. |
Deboss-Wide Cartridge Tears the Mat | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | panelIconId | atlassian-note|||||||
panelIcon | :note: | |||||||
bgColor | #B3F5FF |
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments. The Non-Blade Tool Tears the Corners, Increase the Corner Pause. The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. |
Deboss-Wide Lines are too Long | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Deboss-Wide Lines are too Short | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Deboss-Wide Set to Plunge Between Segments | ||||||||
---|---|---|---|---|---|---|---|---|
Panel | | |||||||
|
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
|
Expand | ||
---|---|---|
| ||
The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool. The Non-Blade Tool leaves a Dot where it plunges, select Unplunge. The Non-Blade Tool takes Too Long to apply, select Plunge. This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change. See: Plunge for Deboss. |
Troubleshooting Button | info|||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
...