52 Degree V-Groove | |
|---|---|
The 52 Degree Cartridge cuts the V-Groove with a 52° bevel. | |
 |
Select the 52 Degree V-Groove Bevel Type | |
|---|---|
Select the 52° Tab on the Configurations screen. Select V-Groove from the Current Bevel Type dropdown control. | |
 |
Select the Area of Concern for 52 Degree V-Grooves Below: |
|---|
52 Degree V-Groove Cuts in the Wrong Place Horizontally | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Horizontal Home. | |
 |
52 Degree V-Groove Cuts in the Wrong Place Vertically | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Vertical Home. | |
 |
52 Degree V-Groove Does Not Pause for Blade Change when Cutting | |
|---|---|
Select this topic to adjust the Plunge Count. | |
 |
52 Degree Circle/Oval V-Groove Rotation Adjustments Using the Circle/Oval Rotation Utility | |
|---|---|
Select this topic to access the Circle/Oval Rotation Utility to adjust the oval rotation for different size ovals. | |
 |
52 Degree V-Groove Exterior Backup is too Long | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Exterior Backup. | |
 |
52 Degree V-Groove Exterior Backup is too Short | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Exterior Backup. | |
 |
52 Degree V-Groove Exterior Overcut is too Long | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Exterior Overcut. | |
 |
52 Degree V-Groove Exterior Overcut is too Short | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Exterior Overcut. | |
 |
52 Degree V-Groove Interior Backup is too Long | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Interior Backup. | |
 |
52 Degree V-Groove Interior Backup is too Short | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Interior Backup. | |
 |
52 Degree V-Groove Interior Overcut is too Long | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Interior Overcut. | |
 |
52 Degree V-Groove Interior Overcut is too Short | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Interior Overcut. | |
 |
52 Degree V-Groove Cuts the Wrong Size | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Opening Adjustment. | |
 |
52 Degree V-Groove Cuts too Thin | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Width Adjustment. | |
 |
52 Degree V-Groove Cuts too Wide | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Width Adjustment. | |
 |
52 Degree V-Groove has an Outside Swoop | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Outside Rotation. | |
 |
52 Degree V-Groove has an Outside Flare | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Outside Rotation. | |
 |
52 Degree V-Groove has an Inside Swoop | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Inside Rotation. | |
 |
52 Degree V-Groove has an Inside Flare | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Inside Rotation. | |
 |
52 Degree Oval V-Groove has an Outside Bump | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Outside Oval Rotation. | |
 |
52 Degree Oval V-Groove has an Outside Feather | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Outside Oval Rotation. | |
 |
52 Degree Oval V-Groove has an Inside Bump | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Inside Oval Rotation. | |
 |
52 Degree Oval V-Groove has an Inside Feather | |
|---|---|
This is viewed from the front of the mat. Select this topic to adjust the Inside Oval Rotation. | |
 |
Troubleshooting Button | |
|---|---|
Use the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. | |
 |