">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 41 Next »

Deboss Medium Definition

 Deboss Medium Definition

The Deboss Medium Red cartridge stylus presses onto the surface of the matboard to create a subtle design with a Medium line.

There are three Deboss stylus sizes: Wide, Medium, Thin.

In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

See: Add Deboss Opening Function

Deboss-Medium is Applied to the Wrong Place Horizontally 

 Deboss Horizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Deboss Cartridges.

If the Deboss line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

If the Deboss line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

See: Horizontal Adjustment for Deboss.

 How to Adjust the Horizontal Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Medium is Applied to the Wrong Place Vertically 

 Deboss Vertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Deboss Cartridges.

If the Deboss line is applied Too Far Up Vertically, Decrease the Vertical Adjustment.

If the Deboss line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

See: Vertical Adjustment for Deboss.

 How to Adjust the Vertical Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Medium is the Wrong Size

 Deboss Opening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Deboss is Too Large, Decrease the Opening Adjustment.

If the Deboss is Too Small, Increase the Opening Adjustment.

See: Opening Adjustment for Deboss.

 How to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Medium Applied at the Wrong Depth

 Deboss Depth Setting Definition

The Depth Setting controls the Blade Depth for the Non-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

See: Depth Setting for Deboss.

Deboss-Medium Cartridge Tears the Mat 

  • The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

  • The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

 Deboss Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

See: Corner Pause for Deboss

Deboss-Medium Lines are too Long

  • If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

 Deboss Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

See: Overshoot for Deboss.

 How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Medium Lines are too Short 

  • If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

 Deboss Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

See: Overshoot for Deboss.

 How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Medium Set to Plunge Between Segments

  • The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

  • The Non-Blade Tool takes Too Long to apply, select Plunge.

 Deboss Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

See: Plunge for Deboss.

Troubleshooting Button 

 Troubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

  • No labels