45 Degree Plus Reverse Bevel Drop Definition |
|---|
The 45°+ Reverse Bevel Drop is created by cutting into the thicker fallout surface with the blade angled at 45°, thereby slanting the bevel under the fallout surface. The matboard core is not visible from the front. The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer. The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut. Select Reverse Drop or Reverse Drop-Front of Mat from the Current Bevel Type dropdown control to edit this configuration. The 45°+ Reverse Bevel Open V-Groove involves two symmetrical cuts: one in the fallout and a corresponding cut in the matboard, both forming a mirrored arrangement a specified distance apart. The matboard core is not visible but the lower layer matboard is visible from the front. First Cut: Cuts the Interior cut into the Fallout Clockwise: Reverse Bevel Drop*. Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise: Reverse Bevel Opening. *The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer. Select Reverse Drop or Reverse Drop-Front of Mat from the Current Bevel Type dropdown control to edit the interior cut configuration. Select Reverse Bevel or Reverse Bevel-Front of Mat from the Current Bevel Type dropdown control to edit the exterior cut configuration. Cutting from the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview. Configurations cut from the Back will only display the bevel type name with no further label; i.e., Normal Bevel. If you are cutting an element that must be applied to the front of the mat, such as a V-Groove or Pen design, any openings on that layer will also cut from the front and use the Front of Mat configuration item; i.e., Normal Bevel - Front of Mat. So if you are having problems with a Normal Bevel cut on the same layer as a V-Groove, make sure you select Normal Bevel - Front of Mat to edit the configurations for that opening. |
45 Degree Plus Drop Cuts Wrong Depth When Using a SKU | |
|---|---|
The Depth Bias is used to calculate the proper Blade Depth when the SKU selected for the matboard contains the Matboard Thickness. The formula is: [(Default Depth) - 10] For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias. See: Depth Bias | |
45 Degree Plus Drop Does Not Pause for Blade Change | |
|---|---|
The Plunge Count controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change. See: Plunge Count | |
45 Degree Plus Drop Exterior Backup is too Long | |
|---|---|
The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup. If the Exterior Backup is cut Too Long, Decrease the Exterior Backup. If the Exterior Backup is cut Too Short, Increase the Exterior Backup. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Exterior Backup is too Short | |
|---|---|
The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup. If the Exterior Backup is cut Too Long, Decrease the Exterior Backup. If the Exterior Backup is cut Too Short, Increase the Exterior Backup. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Exterior Overcut is too Long | |
|---|---|
The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Exterior Overcut is too Short | |
|---|---|
The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Interior Backup is too Long | |
|---|---|
The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Backup is cut Too Long, Decrease the Interior Backup. If the Interior Backup is cut Too Short, Increase the Interior Backup. The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Interior Backup is too Short | |
|---|---|
The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Backup is cut Too Long, Decrease the Interior Backup. If the Interior Backup is cut Too Short, Increase the Interior Backup. The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Interior Overcut is too Long | |
|---|---|
The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Interior Overcut is too Short | |
|---|---|
The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. | |
45 Degree Plus Drop Cuts the Wrong Size | |
|---|---|
The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges. If the Opening is cut Too Large, Decrease the Opening Adjustment. If the Opening is cut Too Small, Increase the Opening Adjustment. | |
45 Degree Plus Drop has a Swoop | |
|---|---|
| |
45 Degree Plus Drop has a Flare | |
|---|---|
A Flare in a Drop is where the corners Curve Away from the Drop. If the Drop has a Flare, Decrease the Rotation. | |
45 Degree Plus Oval Drop has a Bump | |
|---|---|
A Bump in an Oval Drop is a Lump of material left behind where the cut started and ended. If the Oval Drop has a Bump, Increase the Oval Rotation. | |
45 Degree Plus Oval Drop has a Feather | |
|---|---|
A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval. If the Oval Drop has a Feather, Decrease the Oval Rotation. | |
45 Degree Plus Circle/Oval Rotation Utility | |
|---|---|
A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval. If the Oval Drop has a Feather, Decrease the Oval Rotation. A Bump in an Oval Drop is a Lump of material left behind where the cut started and ended. If the Oval Drop has a Bump, Increase the Oval Rotation. | |
Troubleshooting Button | |
|---|---|
Use the /wiki/spaces/FrameShop8x/pages/1942502971 utility to make quick edits to the Configurations for a single object on the Cutting Preview. The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. | |