How Tosectionat:[HowTo...]">Check out our new How To section at: How To...

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 73 Next »

Oval Rotation Definitions

 Oval Rotation Definition

The Oval Rotation controls for Feathers or Bumps on an Oval Opening.

 Feather Definition

A Feather in an Oval Opening is a Fringe of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Feather, Decrease the Oval Rotation.

 Bumps Definition

A Bump in an Oval Opening is a Lump of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Bump, Increase the Oval Rotation.

 Outside Oval Rotation on V-Grooves Definition

The Outside Oval Rotation for V-Grooves controls for Feathers or Bumps on the Outside Cut of an Oval V-Groove.

 Outside V-Groove Feather Definition

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Feather, Increase the Outside Oval Rotation.

 Outside V-Groove Bump Definition

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Bump, Decrease the Outside Oval Rotation.

 Inside Oval Rotation on V-Grooves Definition

The Inside Oval Rotation for V-Grooves controls for Feathers or Bumps on the Inside Cut of an Oval V-Groove.

 Inside V-Groove Feather Definition

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Feather, Decrease the Inside Oval Rotation.

 Inside V-Groove Bump Definition

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Bump, Increase the Inside Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Select the Bevel Type to be Edited:

Oval Rotation on Openings

Problem:

Resolution:

 Feather Definition

A Feather in an Oval Opening is a Fringe of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Feather, Decrease the Oval Rotation.

 Bumps Definition

A Bump in an Oval Opening is a Lump of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Bump, Increase the Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Oval Rotation on Drops

Problem:

Resolution:

 Feather Definition

A Feather in an Oval Opening is a Fringe of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Feather, Decrease the Oval Rotation.

 Bumps Definition

A Bump in an Oval Opening is a Lump of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Bump, Increase the Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Oval Rotation on Outside

Problem:

Resolution:

 Feather Definition

A Feather in an Oval Opening is a Fringe of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Feather, Decrease the Oval Rotation.

 Bumps Definition

A Bump in an Oval Opening is a Lump of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Bump, Increase the Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Oval Rotation on Oval V-Grooves

Problem:

Resolution for Outside Oval V-Groove Cut:

 Outside V-Groove Feather Definition

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Feather, Increase the Outside Oval Rotation.

 Outside V-Groove Bump Definition

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Bump, Decrease the Outside Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Problem:

Resolution for Inside Oval V-Groove Cut:

 Inside V-Groove Feather Definition

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Feather, Decrease the Inside Oval Rotation.

 Inside V-Groove Bump Definition

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Bump, Increase the Inside Oval Rotation.

 How to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

See Also: Troubleshooting Utility for Ovals

Problem:

Resolution:

 Feather V-Groove Definition

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Feather, Increase the Outside Oval Rotation.

If the Inside Oval V-Groove cuts with a Feather, Decrease the Inside Oval Rotation.

 Bump V-Groove Definition

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumps or Feathers on an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Bump, Decrease the Outside Oval Rotation.

If the Inside Oval V-Groove cuts with a Bump, Increase the Inside Oval Rotation.

See Also: Oval Rotation Utility

Problem:

Resolution:

 Feather Definition

A Feather in an Oval Opening is a Fringe of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Feather, Decrease the Oval Rotation.

 Bump Definition

A Bump in an Oval Opening is a Lump of material left behind where the cut started and ended.

The Oval Rotation controls for Bumps or Feathers on an Oval Opening.

If the Oval Opening cuts with a Bump, Increase the Oval Rotation.

  • No labels