Versions Compared

Old Version 52

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Deboss Wide

Definition Expand
titleDeboss Wide Definition

The Deboss Wide Blue cartridge stylus presses onto the surface of the matboard to create a subtle design with a Wide line.

There are three Deboss stylus sizes: Wide, Medium, Thin.

In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

Image RemovedImage RemovedSee: Add Deboss Opening Function

Configurations

Contents:

Horizontally
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleDeboss Horizontal Adjustment Definition
The Horizontal Adjustment defines the global Horizontalplacement of objects applied with the Deboss Cartridges.If the Deboss line is applied Too Far Left
, Increase the Horizontal Adjustment.

If the Deboss line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Image RemovedImage Removed

See: Horizontal Adjustment for Deboss.

Expand
titleHow to Adjust the Horizontal Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
Vertically  Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
If the Deboss line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment.

  • If the Deboss line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

    • Expand
    titleDeboss Vertical Adjustment Definition

    The Vertical Adjustment defines the global Vertical placement of objects applied with the Deboss Cartridges.

    If the Deboss line is applied Too Far Up
    , Decreasethe Vertical Adjustment.

    If the
    line is applied Too Far Down Vertically, Increase the Vertical Adjustment.Image RemovedImage Removed

    See: Vertical Adjustment for Deboss.

    Expand
    titleHow to Adjust the Vertical Adjustment

    When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

    Click OK and do another test cut.

    Continue making adjustments until the desired outcome is achieved.

    Image RemovedImage RemovedDeboss
    Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF
    Expandtitle
    Opening Adjustment DefinitionThe Opening Adjustment controls the size of the Opening cut or Object applied with non
    blade cartridges.

    If the Deboss is Too Large, Decrease the Opening Adjustment.

    If the Deboss is Too Small, Increase the Opening Adjustment.

    Image RemovedImage Removed

    See: Opening Adjustment for Deboss.

    Expand
    titleHow to Adjust the Opening Adjustment

    When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

    Click OK and do another test cut.

    Continue making adjustments until the desired outcome is achieved.

    Image RemovedImage RemovedDeboss-
    Depth Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF
    If the Non-Blade Tool is too Deep, Decrease the
    Setting. Expandtitle

  • If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

    • Depth Setting DefinitionThe Depth Setting controls the Blade Depth for theNon
    Blade Tools in the Configurations.

    If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

    If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

    Image Removed

    See: Depth Setting for Deboss.

    Image RemovedDeboss-
     
    Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF

    • The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

    • The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

    Expand
    titleDeboss Corner Pause Definition

    The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

    The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

    The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

    Image RemovedSee: Corner Pause for Deboss

    Image Removed

    Long
    Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF

    • If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

    Expand
    titleDeboss Overshoot Definition
    The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).If the Overshoot of the Non-Blade Tool is applied Too
    , Decrease the Overshoot.

    If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

    This is similar to the Overcut used with the Blade cartridges.

    Image RemovedImage Removed

    See: Overshoot for Deboss.

    Expand
    titleHow to Adjust the Overshoot

    When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

    Click OK and do another test cut.

    Continue making adjustments until the desired outcome is achieved.

    Image RemovedImage Removed
     

    Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF

    • If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

    Deboss Wide Definition

    Expand
    titleDeboss
    Overshoot
    Expand
    titleHow to Adjust the Overshoot

    When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

    Click OK and do another test cut.

    Continue making adjustments until the desired outcome is achieved.

    Image RemovedImage Removed

    Deboss-Wide Set to Plunge Between Segments

    Panel
    panelIconIdatlassian-note
    panelIcon:note:
    bgColor#B3F5FF

    • The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

    • The Non-Blade Tool takes Too Long to apply, select Plunge.

    Expand
    titleDeboss Plunge Definition

    The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

    The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

    The Non-Blade Tool takes Too Long to apply, select Plunge.

    This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

    Image Removed

    See: Plunge for Deboss.

    Image RemovedImage Removed

    Troubleshooting Button 

    Info
    Expand
    titleTroubleshooting Button Definition

    The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

    Image Removed
    Image Removed
    Wide Definition

    The

    Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

    If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

    If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

    This is similar to the Overcut used with the Blade cartridges.

    Image RemovedImage Removed

    See: Overshoot for Deboss.

    Deboss Wide Blue cartridge stylus presses onto the surface of the matboard to create a subtle design with a Wide line.

    There are three Deboss stylus sizes: Wide, Medium, Thin.

    In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

    Image AddedImage Added

    See: Add Deboss Opening Function