Versions Compared

Version Old Version 4 New Version Current
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

45 Degree Plus Reverse Bevel Drop Definition

Expand
title45°+ Reverse Bevel Drop Full Definition

The 45°+ Reverse Bevel Drop is created by cutting into the thicker fallout surface with the blade angled at 45°, thereby slanting the bevel under the fallout surface. The matboard core is not visible from the front.

The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer.

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Select Reverse Drop or Reverse Drop-Front of Mat from the Current Bevel Type dropdown control to edit this configuration.

Image RemovedImage Removed
Expand
title45°+ Reverse Bevel Open V-Groove Full Definition

The 45°+ Reverse Bevel Open V-Groove involves two symmetrical cuts: one in the fallout and a corresponding cut in the matboard, both forming a mirrored arrangement a specified distance apart. The matboard core is not visible but the lower layer matboard is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise: Reverse Bevel Drop*.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise: Reverse Bevel Opening.

*The Drop is one of the categories within certain opening styles, like the initial section cut of an Open V-Groove. However, it cannot be chosen as a standalone bevel type within Designer.

Select Reverse Drop or Reverse Drop-Front of Mat from the Current Bevel Type dropdown control to edit the interior cut configuration.

Select Reverse Bevel or Reverse Bevel-Front of Mat from the Current Bevel Type dropdown control to edit the exterior cut configuration.

Image RemovedImage RemovedImage Removed

See: 45 Degree Plus Reverse Bevel Drop Configurations

See: 45 Degree Plus Reverse Bevel Opening Configurations

Expand
titleWhen Cutting from the Front

Cutting from the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview.

Configurations cut from the Back will only display the bevel type name with no further label; i.e., Normal Bevel.

If you are cutting an element that must be applied to the front of the mat, such as a V-Groove or Pen design, any openings on that layer will also cut from the front and use the Front of Mat configuration item; i.e., Normal Bevel - Front of Mat.

So if you are having problems with a Normal Bevel cut on the same layer as a V-Groove, make sure you select Normal Bevel - Front of Mat to edit the configurations for that opening.  

Image RemovedImage Removed
Expand
titleHow to Adjust the Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Contents:

PanelpanelIconIdatlassian-notepanelIcon:note:bgColor

#B3F5FF

  • If the Blade Depth is cut Too Deep, Decrease the Depth Bias.

  • If the Blade Depth is cut Too Shallow, Increase the Depth Bias.

Expand
titleDepth Bias Definition
The Depth Bias is used to calculate the properBlade Depth when the SKUselected for the matboard contains the Matboard Thickness.

The formula is: [(Default Depth) - 10]

For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.

Image Removed

See: Depth Bias

Image Removed
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Plunge Count controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  1. Adjust the Plunge Count in the Configuration Screen.

  2. Toggle the Plunge Count to On in the Cut Preview.

  3. See Plunge Count for additional information.

Expand
titlePlunge Count Definition

The Plunge Count controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

Image Removed

See: Plunge Count

Image Removed
Long
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Backup on Drops Definition
The Exterior Backup controls where the Blade Plunges into the Matboard(not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup.

If the Exterior Backup is cut Too
, Decrease the Exterior Backup.

If the Exterior Backup is cut Too Short, Increase the Exterior Backup.

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image RemovedImage Removed

See: Exterior Backup for Drops Configurations

Expand
titleHow to Adjust the Exterior Backup
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.Image RemovedImage Removed

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

panel

panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Backup on Drops Definition
The Exterior Backup controls where the Blade Plunges into the Matboard(not the Fallout) on the Exterior cuts of Drops. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup.

If the Exterior Backup is cut Too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut Too Short, Increase the Exterior Backup.

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image RemovedImage Removed

See: Exterior Backup for Drops Configurations

Expand
titleHow to Adjust the Exterior Backup

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
Long
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Overcut of Drops Definition
The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too
, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Exterior Overcut for Drops Configurations

Expand
titleHow to Adjust the Exterior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

PanelpanelIconId

atlassian-notepanelIcon:note:bgColor#B3F5FF Expand
titleExterior Overcut of Drops Definition
The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Exterior Overcut for Drops Configurations

Expand
titleHow to Adjust the Exterior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
Long
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleInterior Backup on Drops Definition

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Backup is cut Too
, Decrease the Interior Backup.

If the Interior Backup is cut Too Short, Increase the Interior Backup.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Interior Backup for Drops Configurations

Expand
titleHow to Adjust the Interior Backup
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.Image RemovedImage Removed

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

PanelpanelIconIdatlassian-notepanelIcon

:note:bgColor#B3F5FF Expand
titleInterior Backup on Drops Definition

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Backup is cut Too Long, Decrease the Interior Backup.

If the Interior Backup is cut Too Short, Increase the Interior Backup.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Interior Backup for Drops Configurations

Expand
titleHow to Adjust the Interior Backup

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
Long Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
If the Interior Overcut is cut Too Long, Decreasethe Interior Overcut. Expand
titleInterior Overcut on Drops Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too
, Decreasethe Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Interior Overcut for Drops Configurations

Expand
titleHow to Adjust the Interior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
Short Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
If the Interior Overcut is cut Too
, Increase the Interior Overcut.expandImage RemovedImage Removed

See: Interior Overcut for Drops Configurations

Expand
titleHow to Adjust the Interior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed

titleInterior Overcut on Drops Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decreasethe Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Mapillustration.
 
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleOpening Adjustment on Drops Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

Image RemovedImage Removed

See: Opening Adjustment for Drops Configurations

Expand
titleHow to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

 
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Drop has a Swoop, Increase the Rotation.

Expand
titleSwoop on Drops Definition

A Swoop in a Drop is where the corners Curve Inward toward the drop.

If the Drop has a Swoop, Increase the Rotation.

The Rotation controls for Swoops and Flares in Openings.

Image RemovedImage Removed

See: Rotation Configurations

ExpandtitleHow to Adjust the RotationImage RemovedImage Removed

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Drop has a Flare, Decrease the Rotation.

Expand
titleFlare on Drops Definition

A Flare in a Drop is where the corners Curve Away from the Drop.

If the Drop has a Flare, Decrease the Rotation.

Image RemovedImage Removed

See: Rotation Configurations

Expand
titleHow to Adjust the Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed
  Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
If the Oval Drop has a Bump, IncreasetheOval Rotation. Expand
titleBump in Drop Definition
A Bump in an Oval Dropis a Lumpof material left behind where the cut started and ended.If the Oval Drop has a Bump, Increasethe Oval Rotation.Image RemovedImage Removed

See: Oval Rotation Configurations

Expand
titleHow to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

Oval Drop has a Feather  Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
If the
, Decrease the Oval Rotation.
Expand
titleFeathers in Drop Definition

A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval.

If the Oval Drop has a Feather, Decrease the Oval Rotation.

Image RemovedImage Removed

See: Oval Rotation Configurations

Expand
titleHow to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

Image Removed
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleFeathers in Drop Definition

A Feather in an Oval Drop is a Fringe of material left behind where the cut started and ended on the Oval.

If the Oval Drop has a Feather, Decrease the Oval Rotation.

Image RemovedImage Removed

See: Oval Rotation Configurations

Expand
titleBump in Drop Definition
A Bump in an Oval Dropis a Lumpof material left behind where the cut started and ended.If the Oval Drop has a Bump, Increasethe Oval Rotation.Image RemovedImage Removed

See: Oval Rotation Configurations

Expand
titleHow to Adjust the Oval Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image Removed

Troubleshooting Button 

Info

Use the /wiki/spaces/FrameShop8x/pages/1942502971 utility to make quick edits to the Configurations for a single object on the Cutting Preview.

Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Removed
Insert excerpt
45 Degree Plus Reverse Bevel Drop
45 Degree Plus Reverse Bevel Drop
name45 Degree Plus Reverse Bevel Drop