Page Comparison

• The Red Deboss Medium Cartridge presses a medium stylus into the matboard to create a subtle design.

• This is viewed from the front of the mat.

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Select desired Cartridge Tab. 

Select the desired Deboss Cartridge Size from Current Bevel Type.

Edit the desired Configuration field.

Image Removed

• Tool line is applied too far Right:

  • Decrease the Horizontal Adjustment.

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Left, Increase the Horizontal Adjustment.

If the Tool line is applied too far Right, Decrease the Horizontal Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Tool line is applied too far Up:

  • Decrease the Vertical Adjustment.

• Tool line is applied too far Down:

  • Increase the Vertical Adjustment.

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Up, Decrease the Vertical Adjustment.

If the Tool line is applied too far Down, Increase the Vertical Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Opening is cut too Large:

  • Decrease the Opening Adjustment.

• Opening is cut too Small:

  • Increase the Opening Adjustment.

The Opening Adjustment controls the size of the Object cut or applied with non-blade cartridges.

If the Opening is cut too Large, Decrease the Opening Adjustment.

If the Opening is cut too Small, Increase the Opening Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Non-Blade Tool is too Deep:

  • Decrease the Depth Setting.

• Non-Blade Tool is too Shallow:

  • Increase the Depth Setting.

• Non-Blade Tool is Tearing in the Corners of the segments:

  • Increase the Corner Pause. 

• Non-Blade Tool is Pausing Too Long in the Corners of the segments:

  • Decrease the Corner Pause. 

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

• Deboss-Medium Lines are too Long.

• Decrease the Overshoot.

• Increase the Overshoot.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Medium Set to Plunge Between Segments.

• Non-Blade Tool leaves a Dot where it plunges:

  • Select Unplunge.

• Non-Blade Tool takes Too Long to apply:

  • Select Plunge.

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

• Use the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.