Versions Compared

Old Version 37

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Image Removed

Deboss Wide Configurations

Info

  • The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

  • This is viewed from the front of the mat.

Expand
titleCartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Image Removed

Select the Deboss Wide Cartridge Type

  • Select the Deboss Tab on the Configurations screen.  

  • Select the Wide-Blue cartridge from the Cartridge dropdown control.

Tip

  • Deboss Wide

Image Removed

Select the Area of Concern for Wide Deboss Below:

Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.
The

Deboss Wide Configurations

Contents:

Problem:

is applied to thewrong place Horizontally.This
viewed from the front of the mat.

Resolution:

If the Non-BladeTool line is applied too far Left Horizontally, Increase the Horizontal Adjustment.If the Non-BladeTool line is applied too far Right Horizontally, Decrease the Horizontal Adjustment.

  • See Horizontal Adjustment for additional information.

    • Expand
    titleHorizontal Adjustment Definition

    The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

    If the Non-Blade Tool line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

    If the Non-Blade Tool line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

    Image RemovedDeboss-Wide is
     Problem:

    The
    applied to
    wrong place Vertically.

  • This is viewed from the front of the mat.

    • Resolution:

    If the Non-BladeTool line is applied too far Up Vertically, Decrease the Vertical Adjustment.If the Non-BladeTool line is applied too far Down Vertically, Increase the Vertical Adjustment.

  • See Vertical Adjustment for additional information.

    • Expand
    titleVertical Adjustment Definition

    The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

    If the Non-Blade Tool line is applied Too Far Up Vertically, Decrease the Vertical Adjustment.

    If the Non-Blade Tool line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

    Image RemovedDeboss-Wide is the

    Problem:

    • The Deboss-Wide is the Wrong Size.

    • This is viewed from the front of the mat.

    Resolution:

    Expand
    titleOpening Adjustment Definition
    The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.Image Removed

    If the Opening is cut Too Large, Decrease the Opening Adjustment.

    If the Opening is cut Too Small, Increase the Opening Adjustment.

    Problem:

    The
    is applied at the Wrong Depth.

  • This is viewed from the front of the mat.

    • Resolution:

    The Non-BladeTool is too Deep, Decrease the Depth Setting.The Non-BladeTool is too Shallow, Increase the Depth Setting.

  • See Depth Setting for additional information.

    • Expand
    titleDepth Setting Definition
    The Depth Setting controls the Blade Depth for the Non-BladeTools in the Configurations.If the Non-BladeTool is too Deep, Decrease the Depth Setting.If the Non-BladeTool is too Shallow, Increase the Depth Setting.Image RemovedDeboss-Wide
     Problem:
    Cartridge Tears the Mat.

  • This is viewed from the front of the mat.

    • Resolution:

    The Non-BladeTool is Tearing in the Corners of the segments, Increase the Corner Pause. The Non-BladeTool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

  • See Corner Pause for additional information.

    • Expand
    titleCorner Pause Definition
    The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Toolsbetween segments.

    The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

    The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.  

    Image Removed

    Deboss-Wide Lines are too Long

    Problem:

    The Deboss-Wide
    Too Long.

  • This is viewed from the front of the mat.

    • Resolution:

    If the Overshoot is applied
    Long, Decrease the Overshoot.

  • See Overshoot for additional information.

    • Expand
    titleOvershoot Definition

    The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

    This is similar to the Overcut used with the Blade cartridges.

    If the Overshoot of the Non-Blade Tool is applied Too
    , Decrease the Overshoot.

    If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

    Image Removed
     

    Problem:

    The
    Lines are Too Short.

  • This is viewed from the front of the mat.

    • Resolution:

    • If the Overshoot is applied too Long, Decrease the Overshoot.

    • If the Overshoot is applied too Short, Increase the Overshoot.

    • See Overshoot for additional information.

    Expand
    titleOvershoot Definition

    The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

    This is similar to the Overcut used with the Blade cartridges.

    If the Overshoot is applied too Long, Decrease the Overshoot.

    If the Overshoot is applied too Short, Increase the Overshoot.

    Image Removed

    Deboss-Wide Set to Plunge Between Segments

    Problem:

    The Deboss-Wide
    .

  • This is viewed from the front of the mat.

    • Resolution:
    Expand
    titlePlunge Definition

    The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

    The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

    The Non-Blade Tool takes Too Long to apply, select Plunge.

    Image Removed

    The Non-BladeTool leaves a Dot where it plunges, select Unplunge.The Non-BladeTool takes Too Long to apply, select Plunge.

  • See Plunge for additional information.

    •  Image Removed

    Info
    Expand
    titleTroubleshooting Button Definition

    The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

    Insert excerpt
    Deboss Cartridge
    Deboss Cartridge
    nameDeboss Cartridge