Page Comparison

Expand

title	LetterMat Definition

The LetterMat™ fonts are specialized fonts designed specifically for the Wizard FrameShop software.

Single Line Fonts: The letters are formed with Single Lines, not drawn as the outlines of shapes. Single line fonts can only be Debossed or drawn with the Pen.

Outline Fonts: The Outline fonts display the shapes of the letters as outlines with only a slight distinction between the thin and thick strokes. These fonts can be Debossed, Penned or Cut.

Image Removed

See: Add Font Function

See: LetterMat Properties

Expand

title	TTF Definition

The True Type Font (TTF) is an additional source of fonts, separate from LetterMats, that can be loaded into Designer to Cut, Deboss, or Pen.

The True Type Font (TTF) format was created to work between both Apple (Mac) and Microsoft (Windows) and could be deciphered by most printers by default. The TTFs contain the mathematical outlines of each character in the font.

The True Type Fonts are located in the /Windows/Fonts directory.

Note: TTFs have not been tested by Wizard and results may vary. Feel free to experiment.

Image Removed

See: Add Font Function

See: TTF Properties

Expand

title	Deboss Definition

The Deboss cartridge stylus presses onto the surface of the matboard to create a subtle design.

There are three Deboss stylus sizes: Wide, Medium, Thin.

In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

Image Removed

See: Add Deboss Opening Function

See: Deboss Configurations

See: Deboss Thin Definition

See: Deboss Medium Definition

See: Deboss Wide Definition

Expand

title	Pen Definition

The Pen Cartridge is used to draw onto the surface of the matboard on the CMC to create a design.

You can Pen Designs, CutArts, LetterMats and TTFs.

Image Removed

See: Pen Cartridge Configurations

Expand

title	Crease Definition

The Crease Cartridgeis used to apply Crease marks that are used to assist in folding the thicker finished Box.

Image Removed

See: Add Crease Opening Function

See: Crease Cartridge Configurations

Image RemovedDesign Opening in FrameShop

Definition
name	CutArt Definition

Image Added

Design Opening in FrameShop

First we need to make sure we are designing the layers in the correct order for these instructions.
On the FrameShop Main Page, click Admin and stay on the Defaults tab.
Under Layer Direction select Bottom Up if it is not already set to that.
Click Save and return to the Main Page.
- You can change this back to the original setting later if desired.

Panel

panelIconId	1f9d9-200d-2640-fe0f
panelIcon	:woman_mage:
panelIconText	🧙‍♀️
bgColor	#FFEBE6

Layer Direction: Bottom Up is the preferred direction.
- When you Offset an object to create another layer, that new layer will be the Top layer.
Layer Direction: Top Down is not recommended.
- When you Offset an object to create another layer, that new layer will be the Bottom layer, even though it is larger than the original object.

Image Added

Place a two Layer 4 x 5 #101 Rectangle template on the FrameShop Design Editor.

Image Removed

Insert excerpt

	Templates Definition
	Templates Definition
name	Templates Definition

Image Added

Place a Guide

Info
Now we will place a Guide that we can use to align our V-Groove. The V-Groove will be converted into our new Top Layer in Trace.

Right-Click on the opening and select New Guide From Other.

Expandtitle

Insert excerpt

	Guide

Definition

A

	Guide

is a Red line marker which can direct the motion or positioning of objects.The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed


name	Guide Definition

Image Modified

Click the checkbox for Add at Bottom.
Enter 1.5" for the Distance From Bottom field and click OK.

expand

Image Added

title	Guide Definition

A Guide is

a Red line marker which can direct the motion or positioning of objects.The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed

Image RemovedA Guide is

Image Removed

placed at the Bottom of the design.

Expand

title	Guide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed

Image Removed

Image Removed

Image Added

Info
Now we'll use the same steps to place a second Guide that we can use to align the CutArt.

Right-Click on the opening and select New Guide From Other.
Click the checkbox for Add at Bottom.
Enter 1" for the Distance From Bottom field and click OK.

Expand

title	Guide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Added

The second Guide is placed.

Expand

title	Guide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed

Image Removed

Image Added

Place a V-Groove

Info
Now we will place a V-Groove around the opening. This will eventually be our new Top Layer.

Make sure that the Opening is selected.
Click on the Openings tab.
Click the Add V-Groove button.
Enter 1" for the Offset value and click OK.

Expand

title	V-Groove Definition

The

Insert excerpt

	45 Degree Normal Bevel Closed V-Groove

involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.First Cut: Cuts the Interior cut into the Fallout Clockwise.See: 45 Degree

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

Image Removed

45 Degree Normal Bevel Closed V-Groove

Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Expand

title	Offset Definition

The Offset button creates a displacement copy of the selected object a parallel distance away as specified in the Offset Revealfield.

Image Removed

See: Offset Function in Trace

Offset Rules in Trace:

Enclosed Objects:

The Left < button will offset an enclosed object to the outside.
The Right > button will offset an enclosed object to the inside.

Arcs and Curves greater than 180 Degrees use the same rules as closed objects.

Unenclosed Objects:

For unenclosed objects the arrow buttons depend on the direction of travel of the vector segments, starting from the line’s start point. The Left < button offsets Clockwise and Right > button offsets Counter-Clockwise.

If it doesn’t Offset in the expected direction, click Undo and click the other Offset Direction.


name	45 Degree Normal Bevel Closed V-Groove

Image Modified

Info
The V-Groove is placed.

Click on the V-Groove to resize it.

Expandtitle

V-Groove Definition

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

Image Removed

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Image Modified

Pull down the Bottom of the V-Groove and let it snap to the bottom Horizontal Guideline that we placed.
Make sure you are pulling the bottom of the V-Groove down and not just moving it.
Release the mouse

to place it.

Expand

title	V-Groove Definition

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

Image Removed

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Expand

title	Guide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.Click on the Ruler around the design and drag toward the center

to place

a Guide.Select the Guide and click Properties to edit the position or drag

it

where desired

.

Image Removed

Image Modified

titleCutArt

Place CutArt on Design
On the Openings tab, click the Add CutArtbutton.

Expand

Insert excerpt

	CutArt™ Definition
	CutArt™

are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

Image RemovedSee: Add CutArt Function

Definition
name	CutArt Definition

Image Modified

Navigate to the desired location.
Click on the desired CutArt and click Select

. Expand

title	CutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs

.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

Image Removed

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed

Image Removed

Image Modified

The CutArt is placed.
Move the CutArt down to the Top Guide we placed and Center it Horizontally.
- You may need to Zoom In to make the placement easier.

Expand

title	CutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

Image Removed

Expand

title	Guide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

Image Added

Bring Design into Trace
Bring the design into Trace via the Right-Click Menu* or from the Cut Preview Screen. If you use the Right-Click* method, hold down the CTRL key and select the Opening, the V-Groove and the CutArt before selecting Convert to CutArt.

Image Removed

Image Added

Add a Layer

Info
We're going to add a Layer to the Design for our new Top Layer.

Click on the Set Bevels tab.
Click Add in the Layers section.
A new Layer will be added. You can see by the muted design that nothing is currently Traced on this layer

. Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC

.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Image Modified

Trace the Design

Info
We didn't make any changes to the CutArt itself, so there is no need to Tangify It or Convert into Arcs.

Select the Top Layer which is displayed at the top of the Layer List regardless of the actual layer number.
The objects currently Traced on this layer are displayed in their Cartridge Type Colors.

Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Image Modified

Select the Outside Object which will be our new Top Layer.

Image Modified

Click the 45° Bevel Set button to trace it. It will turn Blue.

Info
We're going to Retrace the CutArt and the other opening onto a different Layer which will move them from this Layer.

ExpandtitleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Image Modified

Click on the Middle Layer from the Layer List.

Image Modified

Click the CutArt to select it.
Click the Cartridge Type desired, such as the Penor Deboss Setbutton.

Info
The CutArt will turn the color of the selected

Cartridge.

Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Expandtitle

Cartridge

DefinitionA Cartridge is the physical component that holds the Blade, Deboss Stylus, Pen or other application tool

.

Image Removed

Image Modified

Click on the Middle Mayer object.
Click the 45° Bevel Set button to Trace it. It will turn Blue.

Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Image Modified
Click on the Bottom Layer on the Layer List.	Image Modified
Click on the Bottom Layer object. Click on the 45° Bevel Set button to Trace it. It will turn Blue.

Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

See: Tracing the Design

Image Modified

You can click on each layer on the Layer List and make sure everything is Traced onto the correct layer.

expand

Insert excerpt

title

	Traced
	Traced

Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Expand

title	Bevel Type Definition

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Image Removed


name	Traced Definition

Image Added

Save, Cut

Save the CutArt.
Load the CutArt.
Cut the CutArt.
Optionally, you can also bring the CutArt straight to the Cut Preview from Trace.

Info
The CutArt on lower layer design is completed.

Expand

title	Traced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image Removed

Expand

title	CutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

Image Removed