Page Comparison

• This lesson shows how to make a free-floating unenclosed V-Groove.  

• See Trace Keyboard Shortcuts.

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

The Offset button creates a displacement copy of the selected object a parallel distance away as specified in the Offset Revealfield.

See: Offset Function in Trace

Offset Rules:

Enclosed Objects:

• The Left < button will offset an enclosed object to the outside.

• The Right > button will offset an enclosed object to the inside.

Arcs and Curves greater than 180 Degrees use the same rules as closed objects. 

Unenclosed Objects:

For unenclosed objects the arrow buttons depend on the direction of travel of the vector segments, starting from the line’s start point. The Left < button offsets Clockwise and Right > button offsets Counter-Clockwise.

If it doesn’t Offset in the expected direction, click Undo and click the other Offset Direction.

The Line tool in Trace will draw a Two-Point Line. 

The Line is defined by two points: Initial Position (called an Anchor) and the Terminating Position (called an Anchor).

After it is drawn, a third point in the Center will be displayed, which can be moved to alter the line into an Arc.

See: Line Tool Function

The Line tool in Trace will draw a Two-Point Line. 

The Line is defined by two points: Initial Position (called an Anchor) and the Terminating Position (called an Anchor).

After it is drawn, a third point in the Center will be displayed, which can be moved to alter the line into an Arc.

See: Line Tool Function

• Because this design contains no Arcs, there is no need to Tangify it or Convert Arcs into Splines. 

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

The Arc tool allows you to draw athree-point mathematically defined arc in the Trace software.

The Arc has three points: Initial Position (called an Anchor), Middle Point (called a Handle) which can be moved to change the shape of the Arc, and Terminating Position (called an Anchor).

The Convert Arc to Splines process will convert the Arcs to Splines which are easier to tangify to make cuts smoother.

See: Arc Tool in Trace

See: Arc Tool Definition 

See: Splines Definition

See: Convert Arc to Splines Function

The Tangify function will smooth the connection between the Selected Arc Circuits that are below the specified Angle in the Tangify field to provide a smoother cutting transition between the arcs. 

The Tangify All Circuits will smooth the connection between All of the ArcCircuits that are below the specified Angle in the Tangify field to provide a smoother cutting transition between the arcs. 

See: Tangify Function

See: Tangify All Circuits Function

See: Arc Tool in Trace

See: Arc Tool Definition 

See: Splines Definition

See: Convert Arc to Splines Function

The Convert Arc to Splines process will convert the Arcs to Splines which are easier to tangify to make cuts smoother.

See: Arcs Definition

See: Arcs Tool Function

See: Splines Definition

See: Splines Tool Function

See: Convert Arc to Splines Function

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

• NOTE: V-Groove/Pen/Deboss items do not have to be enclosed objects to be Traced.

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

• The free-floating V-Groove design is completed.

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function