Versions Compared

Old Version 23

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Info

  • Note: Not all cartridges are available for all CMC models.

Image Removed

Pen Cartridge Configurations

Info

  • The Pen Cartridge draws onto the matboard with the selected pen.

  • This is viewed from the front of the mat.

Image Removed

Pen Tab

  • Select the Pen Tab.

  • Select the specific Pen to edit from the Cartridge dropdown control.

  • Note that each pen has its own set of configurations.

  • Below is a list of support documentation for editing the configurations of the Pen Cartridge on the Pen Tab.

Tip

  • Pens 1-9

Image Removed

Pen is Applied to the Wrong Place Horizontally 

Problem:

The

Pen Cartridge Configurations

Contents:

. expandThe

titleHorizontal Adjustment Definition

The Horizontal Adjustment controls where the Deboss is placed Horizontally.

Resolution:

  • If too far left, increase the Pen Horizontal Adjustment.

  • If too far right, decrease the Pen Horizontal Adjustment.

  • See Pen Horizontal Adjustment for additional information.

Image Removed

Pen is Applied to the Wrong Place Vertically 

Problem:

Vertically. Expand
titleVertical Adjustment Definition
The Vertical Adjustment controls specifically where the Deboss is placed
.

Resolution:

  • If too far down, increase the Pen Vertical Adjustment.

  • If too far up, decrease the Pen Vertical Adjustment.

    • See Pen Vertical Adjustment for additional information.

    Image RemovedThe

    Problem:

    is the Wrong Size.
    Expand
    titleOpening Adjustment Definition

    The Opening Adjustment controls the size of the opening.

    Resolution:

    • If cut too small, increase the Pen Opening Adjustment.

    • If cut too large, decrease the Pen Opening Adjustment.

    • See Pen Opening Adjustment for additional information.

    Image RemovedPen See 

    Problem:

    • The Pen is Applied at the Wrong Depth.

    Expand
    titleDepth Setting Definition

    The Depth Setting calculates the proper Blade Depth.

    Resolution:

  • Cut too shallow, increase the Pen Depth Settings.

  • Cut too deep, decrease the Pen Depth Settings.

    • Depth Setting for additional information.Image RemovedPen The

    Problem:

    Cartridge Tears the Mat.
    Expand
    titleCorner Pause Definition

    The Corner Pause controls the amount of time, in milliseconds, to pause the application of the non-blade tools in the corners to avoid tearing the mat.

    Resolution:

    Image RemovedPen

    Problem:

    info

    The
    drawn
    Long. Expand
    titleOvershoot Definition
    The Overshootcontrols how far past each segment the non-blade tool is applied.

    Resolution:

    • Decrease the Pen Overshoot.

    • See Pen Overshoot for additional information.

    Image RemovedPen Lines are too
     

    Problem:

    • The Pen lines are drawn Short.

    Expand
    titleOvershoot Definition
    The Overshootcontrols how far past each segment the non-blade tool is applied.Resolution:Image Removed

    • Increase the Pen Overshoot.

    • See Pen Overshoot for additional information.

    Resolution:

    • Select Plunge to plunge the Pen between Segments.

    • See Plunge for additional information.

    Image Removed

    Problem:

    • Set the Pen to Plunge Between Pen Line Segments.

    Expand
    titlePlunge Definition
    The Plungecontrols whether to Plunge/Unplunge between segments of an object when applying a non-blade tool.

    Problem:

    • How to Calibrate Different Pens.

    Expand
    titleInstall Pen Definition
    The Install Penutility will walk through calibrating for different pens.

    Resolution:

    Use the Install Pen utility to calibrate different pens. Image Removed

  • See Install Pen for additional information.

    • Set Pen Defaults

    Expand
    titleDefault Setting for Pens

    Set up the Pen Defaults in the Admin Editor section of the software.

    Image Removed
    Info

    • Select this topic to see information on the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview.

    Image Removed
    Insert excerpt
    Pen Cartridge
    Pen Cartridge
    namePen Cartridge