Page Comparison

Use the Blade Depth screen to select the Blade Depth for the current layer.

Blade Depth

Click the Blade Depth Button to open the Blade Depth screen which allows the user to set the software blade depth for the current design.

Use the Blade Depth screen to select the Blade Depth for the current layer.

Each time the Blade Depth Knob on the CMC is changed, the Blade Depth setting in the software must be changed to match. Using the correct Blade Depth in the software helps adjust the Backups and Overcuts and other Configuration adjustments to coincide with the Depth selected.

Check the Apply New Depth to All Layers checkbox to apply the selected blade depth to all of the layers of the current design on the Cutting Preview Screen.  

Uncheck the Apply New Depth to All Layers checkbox to select a different blade depth for each layer. 

Select the desired Opening Blade Depth value*  in the Opening field.  If desired, enter notes in the Label field for future references reference for this particular blade depth.

Entering a Label for a blade depth value will make it available from the Blade Depth Quick Select dropdown control.

*This value corresponds to should match the number on the physical Blade Depth dial.

Select the desired V-Groove Blade Depth value*  in the V-Grooves field. If desired, enter notes in the Label field for future references for this particular blade depth.

Entering a Label for a blade depth value will make it available from the Blade Depth Quick Select dropdown control.

*This value corresponds to should match the number on the physical Blade Depth dial.

Click Click the Set As Default button to set the current Blade Depth value as the Default Blade Depth for the associated Opening or V-Groove field.

The default setting for the Blade Depth can be set in the Admin > Cutting section.

This also sets the values for the preset Blade Depth Quick Select Entries.

This is a feature for the VPO Head; not all models have this feature.  

Click Dense Material if this is dense material and Click OK.  

When you Click Cut, the Head plunges at the home position and applies the current air pressure.  

User is prompted to adjust the head pressure to the High Setting. 

See Also: Adjusting the Air Pressure for Dense Matboard for more information.

This is a feature for the VPO Head; not all models have this feature.  

Click Extra Dense Material if this is extra dense material and you are cutting it with the 90° Cartridge.  

Adjust the slidebar to the percentage of cutting speed and click OK. For instance, 50% is 50% of the standard cutting speed.  

When you Click Cut, the Head plunges at the home position and applies the current air pressure.  

User is prompted to adjust the head pressure to the High Setting.

See Also: Adjusting the Air Pressure for Dense Matboard and Cutting an Extra Dense Layer with the 90 Degree Cartridge for more information. 

Changing the blade depth for a layer on the Cutting Preview then returning to the Editor will reload the Default Blade Depth or the selected SKU’s blade depth when you go back to the Cutting Preview.

You will need to reselect the Blade Depth if it should be something other than the Default Blade Depth or the selected SKU’s blade depth.

Optionally, enter the desired Blade Depth in the Blade Depth field.

Optionally, use the Blade Depth Quick Select dropdown control to select one of the preset Blade Depths for the current design.

Click the Blade Depth Quick Select button which is the mat corner sample at the top of the screen on the Cut Preview Screen.

Select the desired preset Blade Depth for the current layer from the dropdown control.

The selected Blade Depth will be applied to the current layer.

After selecting the desired Blade Depth for the current layer and Aligning the Head if necessary, Click Cut to cut the mat.

If the current layer uses a different Cartridge or Blade Depth than the last mat cut, the user will be prompted to change the Cartridge and/or the Blade Depth. 

Replace the current Cartridgewith the one requested on the Cartridge and Blade Depth Prompt.

Change You can change the Blade Depth Value on the screen by clicking on the -/+ buttons to decrease/increase the Blade Depth Value.

The Z1 will automatically adjust the physical Blade Depth of the CMC to this number when you click Continue.

Click Continue to cut.

After selecting the desired Blade Depth for the current layer and Aligning the Head if necessary, Click Cut to cut the mat.

If the current layer requires a different Cartridge or Blade Depth than the last mat cut, the user will be prompted to change the Cartridge and/or the Blade Depth.  

Replace the current Cartridgewith the one requested on the Cartridge and Blade Depth Prompt.

Change the physical Blade Depth Dial on the Head to the requested depth.

Click OK to cut.

Image Removed

Changing the blade depth for a layer on the Cutting Preview then returning to the Editor will reload the Default Blade Depth or the selected SKU’s blade depth when you go back to the Cutting Preview.

You will need to reselect the Blade Depth if it should be something other than the Default Blade Depth or the selected SKU’s blade depth.