Page Comparison

Guides Active

Select whether to activate the Guidesto snap objects to.

Toggle to Guides On to snap objects to Guide Lines.
Toggle to Guides Off to not snap objects to Guide Lines

For Additional Information:

See New Guide in Design.

See Guides Toggle in Design.

See Guidesin Trace.

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

Image Removed

See: Guide Lines Properties

Borders Active

Dynamic Outsides Toggle:

Toggle

Editor Default Setting

Info
Select Dynamic Outsides to add the Border Size to the Bounding Rectangle of the current group of openings, adjusting the outside size as needed. This can be toggled on/off on the Editor. A second opening dragged to the edge of the mat readjusts the outside size by adding the borders around the current openings.

Toggle to Dynamic Outsides On to change the outside dimension dynamically when openings are moved.
Toggle to Dynamic Outsides Off to keep the outside dimension a fixed dimension.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Dynamic Outsides in Design.
See Dynamic Outsides in Visualize.
See Dynamic Outsides in Trace.

Expand

title	Dynamic Outsides Definition

The Dynamic Outsides feature adds the Border Size to the Bounding Rectangle of the current Group of Openings, adjusting the Outside Size as necessary in the Design Editor and Visualize.

Image Removed

Info

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

Expand

title	Guide Definition

Image Removed

Info
Select whether to activate Borders to snap objects to.

Toggle to Borders Onto snap objects to the Border Lines.

Toggle to Borders Off to not snap objects to the Border Lines.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Borders in the New Openings Screen.
See Borders Toggle in Design.
See Borders Properties in Design.
See Borders in Visualize.

Expand

title	Borders Definition

The Border is the area of precisely definable width between the outside edge of a Mat and the edge of the Opening(s) in the Design Editor, Nesting, and Visualization.

Image Removed

See: Border Properties

See: Border Default Settings

Image Removed

Bottom Layer/Top Layer

Info
Select the Positioning direction to position objects.

Toggle to Positioning to Bottom to position objects from the bottom layer.
Toggle to Positioning To Top to position objects from the top layer.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Positioning Toggle in Design.

Expand

title	Positioning Toggle Definition

The Positioning Toggle dictates whether objects are positioned from the Top or from the Bottom Layer as indicated by the Arrow Direction, such as when placing V-Grooves or using the Guides in the Design Editor or Trace.

Image Removed

See: Positioning Toggle Function

Image Removed

Skip New Openings

Info
Select whether to display the New Openings Screen or to go directly to the Design Editor from the Main Screen. Optionally, you can click Cancel on the New Openings Screen to go directly to the Design Editor.

Select Skip ‘New Openings’ to open directly to the Design Editor.
Unselect Skip ‘New Openings’ to open the New Openings Screen.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See New Openings Screen.

Image Removed

Auto Label Multi Openings

Info
Select whether to Auto Label Openings with the size of the object. This size label is overwritten if a new label is manually entered in the object Label field in the Properties tab.

Select Auto Label Multi Openings to label objects with their size.
Unselect Auto Label Multi Openings to not label objects.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:

See Properties in Designfor adding a manual Label.See Options > Show Opening Size Labels in Designto select Show Opening Size Labels.

Image Removed

Enforce Minimum Sizes

Info

Select whether to Enforce Minimum Sizes for CutArt and LetterMat if cutting below the Minimum Size.
Users may experience unsatisfactory results when cutting below the Minimum Size.
Designs can be Debossed/Penned smaller than they can be cut.
The Minimum Size warning is displayed when going to the Cut Preview:
- Yes - Continue cutting without any changes
- No - Resize content to minimums and continue cutting
- Cancel - Abort cutting this design

Select Enforce Minimum Sizes to prompt a warning when cutting below the Minimum Size.
Unselect Enforce Minimum Sizes to not prompt a warning when cutting below the Minimum Size.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:

See Add CutArtin Design.

See Add CutArt Dropdown control in Design.

See CutArt Propertiesin Design.See Add Fontin Design.See Add LetterMatin Design.See LetterMat Propertiesin Design.

See Add LetterMat Dropdown control in Design.

Expand

title	Min Height/Width Definition

Min Height displays the Minimum Height that the selected CutArt or LetterMat has been tested to cut.

The CutArt/LetterMat can be Debossed or Penned at a much smaller size than it can be cut.

Image Removed

See: CutArt Properties

See: LetterMat Properties

Image Removed

Cut the Outside

Info
Select whether to default to Cutting the Outside of the mat.

Select Cut the Outside to cut the outside.
Unselect Cut the Outside to not cut the outside.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:

See Matboard Properties in the Design to turn on/off the Outside cut.

Select Options Menu > Cut Outside on the Cut Previewto cut the outside of the mat. See /wiki/spaces/FrameShop8x/pages/1942506497 on the Cut Previewto turn on/off the Outside cut.See Enable Outside Cutunder Advanced Outside Options on the Cut Previewto toggle on/off the Outside cut.See Cut Outside Using 90 Degree Tool under Set Advanced Optionson the Cut Preview.

See Cut Mode in the Set Advanced Options section on the Cut Preview.

See Remnant Trimming in the Set Advanced Options section on the Cut Preview.

Expand

title	Outside Bevel Definition

The Outside Bevel is created by cutting into the fallout surface with the blade angled at 45°/52°, thereby slanting the bevel under the fallout surface. The matboard core is not visible from the front.

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Select Outside or Outside-Front of Mat from the Current Bevel Type dropdown control to edit this configuration.

Image Removed

See: 45 Degree Outside Configurations

See: 45 Degree Plus Outside Configurations

See: 45 Degree Front Outside Configurations

See: 52 Degree Outside Configurations

See: 90 Degree Outside Configurations

Image Removed

Show Values as Fractions?

Info
Select whether to show the software’s numerical values as Fractions or Decimals.

Select Show Values as Fractions to display numbers as Fractions.
Unselect Show Values as Fractions to display numbers as Decimals.

Image Removed

Wizard Wink Camera

Info
Select whether to show the Wizard Wink Camera settings in the Visualization software.

Select Wizard Wink Camera to display the Wink Camera settings.
Unselect Wizard Wink Camera to not display the Wink Camera settings.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Color Profiles in Visualize for information on creating a color profile for the camera.

Tip
Default Settings: See Admin > Defaults for the default settings for Loading Images.

Expand

title	Visualization Definition

The Visualize software allows the user to create a digitally finished product using the selected frames, matboards and the artwork.

This makes it easy to present several different variations of the design for the customer to pick from.

Image Removed

See: Visualization

Image Removed

Insert excerpt

	Dynamic Outsides
	Dynamic Outsides
name	Dynamic Outsides Definition

Image Added

Related Links
Dynamic Outsides Dynamic Outsides Toggle: Editor Tools Dynamic Outsides Toggle: Trace Dynamic Outsides: Visualize Tools

Versions Compared

Old Version 1

New Version Current

Key

Guides Active

Borders Active

Dynamic Outsides Toggle:

Editor Default Setting

Bottom Layer/Top Layer

Skip New Openings

Auto Label Multi Openings

Enforce Minimum Sizes

Cut the Outside

Show Values as Fractions?

Wizard Wink Camera

Related Links