Versions Compared

Old Version 45

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 46

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Deboss-Medium Cartridge Tears the Mat 

  • The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

  • The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Corner Pause for information on adjusting the Pause of the Non-Blade Tool in the corners.

Expand
titleDeboss Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

See: Corner Pause for Deboss

Image RemovedImage Added

Deboss-Medium Lines are too Long

  • If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Overshoot for information on adjusting the Overshoot of the Non-Blade Tool in the corners.

Expand
titleDeboss Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

See: Overshoot for Deboss.

Expand
titleHow to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

...

Deboss-Medium Set to Plunge Between Segments

  • The Non-Blade Tool leaves a Dot where it plunges, unselect Plunge.

  • The Non-Blade Tool takes Too Long to apply, select Plunge.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Plunge (Tool Specific) for information on adjusting the Plunging of the Non-Blade Tool in the corners.

Expand
titleDeboss Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

See: Plunge for Deboss.

Image RemovedImage Added

Troubleshooting Button 

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

...