Page Comparison

The Vinyl Cartridge uses a special blade to cut the Vinyl which has been temporarily adhered to matboard to create the design.

Image Modified

Image Modified

• If the Vinyl line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

• If the Vinyl line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

The Horizontal Adjustment defines the global Horizontalplacement of objects applied with the Vinyl Cartridges.

If the Vinyl line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

If the Vinyl line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Image ModifiedImage Modified

See: Horizontal Adjustment for Vinyl.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• If the Vinyl line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment.

• If the Vinyl line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

The Vertical Adjustment defines the global Vertical placement of objects applied with the Vinyl Cartridges.

If the Vinyl line is applied Too Far Up Vertically, Decreasethe Vertical Adjustment.

If the Vinyl line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

Image ModifiedImage Modified

See: Vertical Adjustment for Vinyl.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• If the Vinyl is cut Too Large, Decrease the Opening Adjustment.

• If the Vinyl is cut Too Small, Increase the Opening Adjustment.

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Vinyl is cut Too Large, Decrease the Opening Adjustment.

If the Vinyl is cut Too Small, Increase the Opening Adjustment.

Image Modified

Image Modified

See: Opening Adjustment for Vinyls.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

• If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

The Depth Setting controls the Blade Depth for theNon-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

Image Modified

See: Depth Setting for Vinyl.

• The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

• The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool Tears the Corners, Increase the Corner Pause. 

The Non-Blade Tool is pausing too long in the Corners, Decrease the Corner Pause. 

Image Modified

Image Modified

See: Corner Pause for Vinyl

• If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image ModifiedImage Modified

See: Overshoot for Vinyl.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image ModifiedImage Modified

See: Overshoot for Vinyl.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

• The Non-Blade Tool takes Too Long to apply, select Plunge.

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

Image Modified

Image Modified

See: Plunge for Vinyl.

• Select this topic to see information on the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview.

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Modified