Versions Compared

Old Version 40

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 41

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Deboss Medium Configurations

InfoThe Red Deboss Medium Cartridge presses a medium stylus into

Deboss Medium Definition

Expand
titleDeboss Medium Definition

The Deboss Medium Red cartridge stylus presses onto the surface of the matboard to create a subtle design

.
Expand
titleCartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Image Removed

Select the Deboss Medium Cartridge Type

Expand
titleHow to Select the Bevel Type to Edit

Select desired Cartridge Tab. 

Select the desired Deboss Cartridge Size from Current Bevel Type.

Edit the desired Configuration field.

Image Removed

Select the Area of Concern for Medium Deboss Below:

Be sure to select the Deboss Medium from the Current Bevel Type dropdown control.

with a Medium line.

There are three Deboss stylus sizes: Wide, Medium, Thin.

In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

Image AddedImage Added

See: Add Deboss Opening Function

Problem:

Deboss-Medium is Applied to the Wrong Place Horizontally 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Deboss-Medium is applied to the Wrong Place Horizontally.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Tool If the Deboss line is applied too far Left:Too Far Left Horizontally, Increase the Horizontal Adjustment.

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Tool If the Deboss line is applied too far Right:Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Expand
titleDeboss Horizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontalplacement of objects applied with the Non-Blade Tool Deboss Cartridges.

If the Tool Deboss line is applied too far Too Far Left Horizontally, Increase the Horizontal Adjustment.

If the Tool Deboss line is applied too far Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Image AddedImage Added

See: Horizontal Adjustment for Deboss.

Expand
titleHow to Adjust the Horizontal Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image AddedImage Modified
Problem:

Deboss-Medium is Applied to the Wrong Place Vertically 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Deboss-Medium is applied to the Wrong Place Vertically.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Tool If the Deboss line is applied too far Up:Too Far Up Vertically, Decreasethe Vertical Adjustment.

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Tool If the Deboss line is applied too far Down:Too Far Down Vertically, Increase the Vertical Adjustment.

Expand
titleDeboss Vertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Deboss Cartridges.

If the Tool Deboss line is applied too far Too Far Up Vertically, Decreasethe Vertical Adjustment.

If the Tool Deboss line is applied too far Too Far Down Vertically, Increase the Vertical Adjustment.

Image AddedImage Added

See: Vertical Adjustment for Deboss.

Expand
titleHow to Adjust the Vertical Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image AddedImage Modified
Problem:

Deboss-Medium is the Wrong Size

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Deboss -Medium is the Wrong Size.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleDeboss Opening Adjustment Definition

The Opening Adjustment controls the size of the Object Opening cut or Object applied with non-blade cartridges.

If the Opening Deboss is cut too Too Large, Decrease the Opening Adjustment.

If the Opening Deboss is cut too Too Small, Increase the Opening Adjustment.

Image AddedImage Added

See: Opening Adjustment for Deboss.

Expand
titleHow to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image AddedImage Modified
Problem:

Deboss-Medium Applied at the Wrong Depth

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Deboss-Medium is applied at the Wrong Depth.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Non-Blade Tool is too Shallow:, Increase the Depth Setting.

Expand
titleDeboss Depth Setting Definition

The Depth Setting controls the Blade Depth for theNon-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

Image Modified

Deboss-Medium Cartridge Tears the Mat 

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
The

See: Depth Setting for Deboss.

Image Added

Problem:

PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FF.Resolution:

Deboss-Medium Cartridge Tears the Mat

 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Non-Blade Tool is Tearing in Tears the Corners of the segments:, Increase the Corner Pause. 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Non-Blade Tool is Pausing Too Long pausing too long in the Corners of the segments:, Decrease the Corner Pause. 

Expand
titleDeboss Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool is Tearing in Tears the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long pausing too long in the Corners of the segments, Decrease the Corner Pause. 

Image Modified

Deboss-Medium Lines are too Long

See: Corner Pause for Deboss

Image AddedImage Added
. Resolution:

Deboss-Medium Lines are too Long

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

Expand
titleDeboss Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied too Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image AddedImage Added

See: Overshoot for Deboss.

Expand
titleHow to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image ModifiedImage Added
Problem:

Deboss-Medium Lines are too Short 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Deboss-Medium Lines are too Short.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

Expand
titleDeboss Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied too Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image AddedImage Added

See: Overshoot for Deboss.

Expand
titleHow to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image AddedImage Modified
Problem:

Deboss-Medium Set to Plunge Between Segments

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Deboss-Medium Set to Plunge Between Segments.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Non-Blade Tool leaves a Dot where it plunges:

    Select

    , select Unplunge.

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Non-Blade Tool takes Too Long to apply:

    Select

    , select Plunge.

Expand
titleDeboss Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

This is different from the Plunge Count which controls the number of Blade Plunges for each Blade Cartridge before pausing for a Blade Change.

Image ModifiedImage Added

See: Plunge for Deboss.

Image AddedImage Added

Troubleshooting Button 

Info
Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Added
Image Modified