Page Comparison

• The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

• Deboss-Wide is applied to thewrong place Horizontally.

• Non-Blade Tool line is applied too far Left:

  • Increase the Horizontal Adjustment.

• Non-Blade Tool line is applied too far Right:

  • Decrease the Horizontal Adjustment.

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Left, Increase the Horizontal Adjustment.

If the Non-Blade Tool line is applied Too Far Right, Decrease the Horizontal Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide is applied to the wrong place Vertically.

• Non-Blade Tool line is applied too far Up:

  • Decrease the Vertical Adjustment.

• Non-Blade Tool line is applied too far Down:

  • Increase the Vertical Adjustment.

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Up, Decrease the Vertical Adjustment.

If the Non-Blade Tool line is applied Too Far Down, Increase the Vertical Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide is the Wrong Size.

• Opening cuts too Large:

  • Decrease the Opening Adjustment.

• Opening cuts too Small:

  • Increase the Opening Adjustment.

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide is applied at the Wrong Depth.

• Non-Blade Tool is too Deep:

  • Decrease the Depth Setting.

• Non-Blade Tool is too Shallow:

  • Increase the Depth Setting.

The Depth Setting controls the Blade Depth for the Non-BladeTools in the Configurations.

If the Non-BladeTool is too Deep, Decrease the Depth Setting.

If the Non-BladeTool is too Shallow, Increase the Depth Setting.

• Deboss-Wide Lines are Too Short.

• Increase the Overshoot.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Deboss-Wide Set to Plunge Between Segments.

• Non-Blade Tool leaves a Dot where it plunges:

  • Select Unplunge.

• Non-Blade Tool takes Too Long to apply:

  • Select Plunge.

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.