Page Comparison

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Deboss Wide Configurations

Info
The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design. This is viewed from the front of the mat.

Expand

title	Cartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Select the Deboss Wide Cartridge Type

Select the Deboss Tab on the Configurations screen.
Select the Wide-Blue cartridge from the Cartridge dropdown control.

Tip
Deboss Wide

Select the Area of Concern for Wide Deboss Below: Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.

Deboss-Wide is Applied to the Wrong Place Horizontally

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide is applied to thewrong place Horizontally.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Non-Blade Tool line is applied too far Left:
- Increase the Horizontal Adjustment.

Non-Blade Tool line is applied too far Right:
- Decrease the Horizontal Adjustment.

See Horizontal Adjustment for additional information.

Expand

title	Horizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Left, Increase the Horizontal Adjustment.

If the Non-Blade Tool line is applied Too Far Right, Decrease the Horizontal Adjustment.

Image Removed

Deboss-Wide is Applied to the Wrong

Expand

title	How to Adjust the Horizontal Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image Added

Deboss-Wide is Applied to the Wrong Place Vertically

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide is applied to the wrong place Vertically.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Non-Blade Tool line is applied too far Up:
- Decrease the Vertical Adjustment.

Non-Blade Tool line is applied too far Down:
- Increase the Vertical Adjustment.

See Vertical Adjustment for additional information.

Expand

title	Vertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Up, Decrease the Vertical Adjustment.

If the Non-Blade Tool line is applied Too Far Down, Increase the Vertical Adjustment.

Image Removed

Deboss-Wide is the Wrong Size

Expand

title	How to Adjust the Vertical Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image Added

Deboss-Wide is the Wrong Size

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide is the Wrong Size.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Opening cuts too Large:
- Decrease the Opening Adjustment.

Opening cuts too Small:
- Increase the Opening Adjustment.

See Opening Adjustment for additional information.

Expand

title	Opening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment Small, Increase the Opening Adjustment.

Expand

title	How to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Wide Applied at the Wrong Depth

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide is applied at the Wrong Depth.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Non-Blade Tool is too Deep:
- Decrease the Depth Setting.

Non-Blade Tool is too Shallow:
- Increase the Depth Setting.

See Depth Setting for additional information.

Expand

title	Depth Setting Definition

The Depth Setting controls the Blade Depth for the Non-BladeTools in the Configurations.

If the Non-BladeTool is too Deep, Decrease the Depth Setting.

If the Non-BladeTool is too Shallow, Increase the Depth Setting.

Deboss-Wide Cartridge Tears the Mat

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide Cartridge Tears the Mat.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Non-Blade Tool is Tearing in the Corners of the segments:
- Increase the Corner Pause.

Non-Blade Tool is Pausing Too Long in the Corners of the segments:
- Decrease the Corner Pause.

See Corner Pause for additional information.

Expand

title	Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Toolsbetween segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause.

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.

Deboss-Wide Lines are too Long

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide Lines are Too Long.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Overshoot is too Long:
Decrease the Overshoot.

See Overshoot for additional information.

Expand

title	Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot Short, Increase the Overshoot.

Expand

title	How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Wide Lines are too Short

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide Lines are Too Short.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Overshoot is too Short:
Increase the Overshoot.

See Overshoot for additional information.

Expand

title	Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

Expand

title	How to Adjust the Overshoot

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Deboss-Wide Set to Plunge Between Segments

Problem:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Deboss-Wide Set to Plunge Between Segments.
- This is viewed from the front of the mat.

Resolution:

Panel

panelIconId	atlassian-note
panelIcon	:note:
bgColor	#B3F5FF

Non-Blade Tool leaves a Dot where it plunges:
- Select Unplunge.

Non-Blade Tool takes Too Long to apply:
- Select Plunge.

See Plunge for additional information.

Expand

title	Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

Troubleshooting Button

Info
Use the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview.

Expand

title	Troubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

...

Versions Compared

Old Version 42

New Version 43

Key

Cartridges Involved

Deboss Wide Configurations

Select the Deboss Wide Cartridge Type

Select the Area of Concern for Wide Deboss Below:

Deboss-Wide is Applied to the Wrong Place Horizontally

Problem:

Resolution:

Deboss-Wide is Applied to the Wrong Place Vertically

Problem:

Resolution:

Deboss-Wide is the Wrong Size

Deboss-Wide is the Wrong Size

Problem:

Resolution:

Deboss-Wide Applied at the Wrong Depth

Problem:

Resolution:

Deboss-Wide Cartridge Tears the Mat

Problem:

Resolution:

Deboss-Wide Lines are too Long

Problem:

Resolution:

Deboss-Wide Lines are too Short

Problem:

Resolution:

Deboss-Wide Set to Plunge Between Segments

Problem:

Resolution:

Troubleshooting Button