Cartridges Involved |
---|
This Configuration element involves the following Cartridges.
Note: Cartridges Involved |
---|
This Configuration element involves the following Cartridges. Note: Not all cartridges are available for all CMC models. | |
Deboss Wide Configurations |
---|
Expand |
---|
title | Cartridge Definition |
---|
| A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
| |
Select the Deboss Wide Cartridge Type |
---|
| |
Select the Area of Concern for Wide Deboss Below: |
---|
|
---|
Problem:Resolution: Expand |
---|
title | Horizontal Adjustment Definition |
---|
| The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridgesthe global Horizontal placement of objects applied with the Non-Blade Tool Cartridges. If the Tool line is applied too far Left Horizontally, Increase the Horizontal Adjustment. If the Tool line is applied too far Right Horizontally, Decrease the Horizontal Adjustment. |
| |
|
---|
Problem:Resolution: Expand |
---|
title | Vertical Adjustment Definition |
---|
| The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool CartridgesVertical Adjustment Definition |
| The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges. If the Tool line is applied too far Up Vertically, Decrease the Vertical Adjustment. If the Tool line is applied too far Down Vertically, Increase the Vertical Adjustment. |
| |
|
---|
Problem:Resolution: Expand |
---|
title | Opening Adjustment Definition |
---|
| The Opening Adjustment controls the size of the object Object cut or applied with non-blade cartridges-blade cartridges. If the Opening is cut too Large, Decrease the Opening Adjustment. If the Opening is cut too Small, Increase the Opening Adjustment. |
| |
|
---|
Problem:Resolution: Expand |
---|
title | Depth Setting Definition |
---|
| The Depth Setting controls the Blade Depth for the Non-Blade Tools in the Configurations. If the Non-Blade Tool is too Deep, Decrease the Depth Setting. If the Non-Blade Tool is too Shallow, Increase the Depth Setting. |
| |
|
---|
Problem:Resolution:The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. See Corner Pause for additional information.
Expand |
---|
title | Corner Pause Definition |
---|
| The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.to pause the application of the Non-Blade Tools between segments. The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. |
| |
|
---|
Problem:Resolution:If the Overshoot is applied too Long, Decrease the Overshoot. See Overshoot for additional information.
Expand |
---|
title | Overshoot Definition |
---|
| The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl). This is similar to the Overcut used with the Blade cartridgesis similar to the Overcut used with the Blade cartridges. If the Overshoot is applied too Long, Decrease the Overshoot. If the Overshoot is applied too Short, Increase the Overshoot. |
| |
|
---|
Problem:Resolution:If the Overshoot is applied too Long, Decrease the Overshoot. If the Overshoot is applied too Short, Increase the Overshoot. See Overshoot for additional information.
Expand |
---|
title | Overshoot Definition |
---|
| The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl). This is similar to the Overcut used with the Blade cartridges. If the Overshoot is applied too Long, Decrease the Overshoot. If the Overshoot is applied too Short, Increase the Overshoot. |
| |
|
---|
Problem:Resolution:The Non-Blade Tool leaves a Dot where it plunges, select Unplunge. The Non-Blade Tool takes Too Long to apply, select Plunge. See Plunge for additional information.
Expand |
---|
| The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Segments of an object when applying a Non-Blade Tool. The Non-Blade Tool leaves a Dot where it plunges, select Unplunge. The Non-Blade Tool takes Too Long to apply, select Plunge. |
| |
|
---|
Expand |
---|
title | Troubleshooting Button Definition |
---|
| The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. |
| |