">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 43 Next »

Select the Configurations Cartridge Type to Edit

  • Select the desired Cartridge Type Tab to edit the configurations for that Cartridge.

  • Examples of the Cartridges are listed below.

45 Degree Cartridge

  • The 45° Cartridge cuts the Bevel Angle on the matboard at 45°.

  • This Bevel Angle is displayed on the Front or the Back of the mat depending upon the selected Bevel Type.

  • The 45° Blade Cartridge does not support Blade Depths above 16.

45MetalBevelOpeningCartridge70800.png

Full Definition: 45 Degree Cartridge Definition

45 Degree+ Cartridge

  • The 45°+ Cartridge cuts the Bevel Angle on the thicker matboard at 45°.

    • The 45°+ Blade Cartridge supports Blade Depths above 16.

  • This Bevel Angle is displayed on the Front or the Back of the mat depending upon the selected Bevel Type.

  • The 45°+ Blade Cartridge is not selected within the Editor; it is set by using a Blade Depth above 16 on the Cut Preview.

45PlusMetalBevelOpening70800.png

Full Definition: 45 Degree Plus Cartridge Definition

45 Degree Front Cartridge

  • The 45° Front Cartridge cuts the Bevel Angle on the matboard from the Front at 45°.

  • This Bevel Angle is displayed on the Front or the Back of the mat depending upon the selected Bevel Type.

  • The 45° Front Blade Cartridge is not selected within the Editor; it is set by setting Cut From Front on the Cut Preview.

45FrontMetalBevelOpening70800.png

Full Definition: 45 Degree Front Cartridge Definition

52 Degree Cartridge

  • The 52° Cartridge cuts the Bevel Angle on the matboard at 52°.

  • This Bevel Angle is displayed on the Front or the Back of the mat depending upon the selected Bevel Type.

52PlasticBevelOpening70800.png

90 Degree Cartridge

  • The 90° Cartridge cuts a 90° Right Angle into the matboard.

  • The matboard core is hidden from view since there is no Bevel when cutting at a 90° Right Angle.

90BevelOpeningCartridge70800.png

Crease Cartridge

  • The Crease Cartridge is used to apply Crease marks that are used to assist in folding the thicker finished Box.

  • The Crease Cartridge is labeled in the software with a Perforation Symbol.

Full Definition: Crease Cartridge Definition

Deboss Cartridges

  • The Deboss Cartridge stylus presses onto the surface of the matboard to create a subtle design.

  • There are three Deboss Cartridge sizes with a Deboss Symbol on the Cartridge end: Thin, Medium, Wide.

DebossingImagesCartridges70800.png

Full Definition: Deboss Cartridge Definition

Pen Cartridge

  • The Pen Cartridge holds a pen to the matboard to draw onto the matboard. 

  • The Pen Cartridge is used to draw onto the surface of the matboard on the CMC to create a design.

  • The Pen is labeled in the software with a Pen Tip Icon.

PenCartridge70800.png

Full Definition: Pen Cartridge Definition

Vinyl Cartridge

  • The Vinyl Cartridge cuts designs into a sheet of Vinyl which has been temporarily adhered to the matboard. 

  • The Vinyl Cartridge uses a special blade to cut the Vinyl which has been temporarily adhered to the matboard to create the design.

  • The Vinyl is labeled in the software with a thin Vinyl Blade Icon.

Full Definition: Vinyl Cartridge Definition

  • No labels