Versions Compared

Old Version 43

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Crease Cartridge

Definition Expand
titleCrease Cartridge Definition
The Crease Cartridgeis used to apply Perforationmarks that are used to assist in folding the thicker finished Box.Image RemovedImage Removed

Configurations

Contents:

  • If the Backup is cut Too Long, Decrease the Backup.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleCrease Exterior Backup Definition
The Backup controls where the Blade Plunges into the Matboard(not the Fallout) on the Exterior cuts of Openings. 

If the Backup is cut Too Long, Decrease the Backup.

If the Backup is cut Too Short, Increase the Backup.

The Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image RemovedImage Removed

See: Backup for Creases.

Expand
titleHow to Adjust the Exterior Backup

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed

  • If the Backup is cut Too Short, Increase the Backup.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleCrease Exterior Backup Definition
The Backup controls where the Blade Plunges into the Matboard(not the Fallout) on the Exterior cuts of Openings. 

If the Backup is cut Too Long, Decrease the Backup.

If the Backup is cut Too Short, Increase the Backup.

The Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image RemovedImage Removed

See: Backup for Creases.

Expand
titleHow to Adjust the Exterior Backup

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image RemovedImage Removed

  • If the Overcut is cut Too Long, Decrease the Overcut.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleCrease Exterior Overcut Definition
The Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

If the Overcut is cut Too Long, Decrease the Overcut.

If the Overcut is cut Too Short, Increase the Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Overcut for Creases.

Expand
titleHow to Adjust the Exterior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

  • If the Overcut is cut Too Short, Increase the Overcut.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleCrease Exterior Overcut Definition
The Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

If the Overcut is cut Too Long, Decrease the Overcut.

If the Overcut is cut Too Short, Increase the Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.Image RemovedImage Removed

See: Overcut for Creases.

Expand
titleHow to Adjust the Exterior Overcut

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleCrease Opening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Crease is Too Large, Decrease the Opening Adjustment.

If the Crease is Too Small, Increase the Opening Adjustment.

Image RemovedImage Removed

See: Opening Adjustment for Creases.

Expand
titleHow to Adjust the Opening Adjustment

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.Image RemovedImage Removed

Continue making adjustments until the desired outcome is achieved.

If the Blade Depth is cut Too Deep, Decrease the Depth Bias.

If the Blade Depth is cut Too Shallow, Increase the Depth Bias.

The formula is: [(Default Depth) - 10]

For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.

Image Removed

See: Depth Bias

Expand
titleHow to Adjust the Depth Bias

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Image Removed

Troubleshooting Button 

  • Select this topic to see information on editing with the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6
Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Removed
Image Removed

  • If the Blade Depth is cut Too Deep, Decrease the Depth Bias.

  • If the Blade Depth is cut Too Shallow, Increase the Depth Bias.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information:

  • See Depth Bias for information on setting the Depth Bias.

  • See Matboard Properties for information on assigning matboard SKUs to each layer of the design in Designer.

  • See Mat SKUs for information on assigning matboard SKUs to each layer of the design in Visualize.

  • See Frame SKUs for information on assigning Frame SKUs to each layer of the design in Visualize.

  • See Assign SKU to Layer for more information on Assigning a SKU to a Layer on the Cut Preview.

Tip

  • Default Settings:

  • See Admin > Subscription for the default settings for Subscribing to Vendors.

  • See Admin > Frames for the default settings for Frame Records for Vendors you are Subscribed to.

  • See Admin > Mats for the default settings for Mat Records for Vendors you are Subscribed to.

Expand
titleDepth Bias Definition
The Depth Bias is used to calculate the properBlade Depth when the SKUselected for the matboard contains the Matboard Thickness.

Crease Cartridge Definition

Expand
titleCrease Cartridge Definition

The Crease Cartridgeis used to apply Perforationmarks that are used to assist in folding the thicker finished Box.

Image AddedImage Added