Crease Cartridge Definition
| title | Crease Cartridge Definition |
|---|
Crease Backup is too Long
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Crease Exterior Backup Definition |
|---|
If the Backup is cut Too Long, Decrease the Backup.
If the Backup is cut Too Short, Increase the Backup.
The Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.
See: Backup for Creases.
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Backup is too Short
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Crease Exterior Backup Definition |
|---|
If the Backup is cut Too Long, Decrease the Backup.
If the Backup is cut Too Short, Increase the Backup.
The Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.
See: Backup for Creases.
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Overcut is too Long
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Crease Exterior Overcut Definition |
|---|
If the Overcut is cut Too Long, Decrease the Overcut.
If the Overcut is cut Too Short, Increase the Overcut.
The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: Overcut for Creases.
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Overcut is too Short
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Crease Exterior Overcut Definition |
|---|
If the Overcut is cut Too Long, Decrease the Overcut.
If the Overcut is cut Too Short, Increase the Overcut.
The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: Overcut for Creases.
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease is the Wrong Size
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| Expand | ||
|---|---|---|
| ||
The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges. If the Crease is Too Large, Decrease the Opening Adjustment. If the Crease is Too Small, Increase the Opening Adjustment. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
If the Blade Depth is cut Too Deep, Decrease the Depth Bias.
If the Blade Depth is cut Too Shallow, Increase the Depth Bias.
The formula is: [(Default Depth) - 10]
For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.
See: Depth Bias
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Troubleshooting Button
| Info |
|---|
|
| Expand | ||
|---|---|---|
| ||
The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. |
Set Box Defaults
| title | Default Settings for the Box Utility |
|---|
Set up the Box Defaults for the Crease cartridge in the Admin Editor section of the software.
Contents: |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Depth Bias Definition |
|---|
|