Cartridges Involved
This Configuration element involves the following Cartridges.
| Info |
|---|
Note: Not all cartridges are available for all CMC models. |
Crease Cartridge Configurations
| Info |
|---|
|
| Expand | ||
|---|---|---|
| ||
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
Crease Tab
Select the Deboss Tab on the Configurations screen.
Select the Crease Cartridge.
Crease Exterior Backup is too Long
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| Expand | ||
|---|---|---|
| ||
The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cut. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration. If the Exterior Backup is cut too Short, it can leave a Hook in the corner. If the Exterior Backup is cut too Long, Decrease the Exterior Backup. If the Exterior Backup is cut too Short, Increase the Exterior Backup. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Exterior Backup is too Short
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| Expand | ||
|---|---|---|
| ||
The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cut. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration. If the Exterior Backup is cut too Short, it can leave a Hook in the corner. If the Exterior Backup is cut too Long, Decrease the Exterior Backup. If the Exterior Backup is cut too Short, Increase the Exterior Backup. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Exterior Overcut is too Long
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| Expand | ||
|---|---|---|
| ||
The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut too Short, Increase the Exterior Overcut. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease Exterior Overcut is too Short
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| Expand | ||
|---|---|---|
| ||
The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut too Short, Increase the Exterior Overcut. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Crease is the Wrong Size
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| panelIconId | atlassian-note |
|---|---|
| panelIcon | :note: |
| bgColor | #B3F5FF |
Opening is too Large:
Decrease the Opening Adjustment.
Opening is too Small:
Increase the Opening Adjustment.
| Expand | ||
|---|---|---|
| ||
The Opening Adjustment controls the size of the Object cut or applied with non-blade cartridges. If the Opening is cut too Large, Decrease the Opening Adjustment. If the Opening is cut too Small, Increase the Opening Adjustment. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Troubleshooting Button
| Info |
|---|
|
| Expand | ||
|---|---|---|
| ||
The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure. |
Set Box Defaults
| title | Default Settings for the Box Utility |
|---|
Set up the Box Defaults for the Crease cartridge in the Admin Editor section of the software.
Contents: |
Problem:
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
Resolution:
| panelIconId | atlassian-note |
|---|---|
| panelIcon | :note: |
| bgColor | #B3F5FF |
The Crease Blade Depth is too Deep:
Decrease the Depth Bias.
The Crease Blade Depth is too Shallow:
Increase the Depth Bias.
| title | Depth Bias Definition |
|---|
The formula is: [(Default Depth) - 10]
For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.
|