Versions Compared

Old Version 27

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 28

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Place CutArt on a Different Layer

Info

  • CutArt are simple shapes and design elements that can be cut, drawn, or Debossed.

  • Traditionally, CutArts can only be placed on the top layer. This lesson shows how to retrace a CutArt onto a Different Layer other than the top layer. 

  • You can also use these same steps to place a LetterMat, TTF, Deboss, Pen or Crease object onto a different layer other than the Top Layer.

Panel
panelIconId1f9d9-200d-2640-fe0f
panelIcon:woman_mage:
panelIconText🧙‍♀️
bgColor#FFEBE6
Expand
titleCutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function

Expand
titleLetterMat Definition

The LetterMat™ fonts are specialized fonts designed specifically for the Wizard FrameShop software.

Single Line Fonts: The letters are formed with Single Lines, not drawn as the outlines of shapes. Single line fonts can only be Debossed or drawn with the Pen.

Outline Fonts: The Outline fonts display the shapes of the letters as outlines with only a slight distinction between the thin and thick strokes. These fonts can be Debossed, Penned or Cut.

See: Add Font Function

See: LetterMat Properties

Expand
titleTTF Definition

The True Type Font (TTF) is an additional source of fonts, separate from LetterMats, that can be loaded into Designer to Cut, Deboss, or Pen.

The True Type Font (TTF) format was created to work between both Apple (Mac) and Microsoft (Windows) and could be deciphered by most printers by default. The TTFs contain the mathematical outlines of each character in the font.

The True Type Fonts are located in the /Windows/Fonts directory.

Note: TTFs have not been tested by Wizard and results may vary. Feel free to experiment.

See: Add Font Function

See: TTF Properties

Expand
titleDeboss Definition

The Deboss cartridge stylus presses onto the surface of the matboard to create a subtle design.

There are three Deboss stylus sizes: Wide, Medium, Thin.

In addition to Template Shapes, you can also Deboss CutArts, LetterMats and TTFs.

DebossWideCartridgeConfig70800.jpg

See: Add Deboss Opening Function

See: Deboss Configurations

See: Deboss Thin Definition

See: Deboss Medium Definition

See: Deboss Wide Definition

Expand
titlePen Definition

The Pen Cartridge is used to draw onto the surface of the matboard on the CMC to create a design.

You can Pen Designs, CutArts, LetterMats and TTFs.

PenCartridgeConfig70800.jpg

See: Pen Cartridge Configurations

Expand
titleCrease Definition

The Crease Cartridgeis used to apply Crease marks that are used to assist in folding the thicker finished Box.

CreaseCartridgeConfig70800.jpg

See: Add Crease Opening Function

See: Crease Cartridge Configurations

Image RemovedImage Added

Design Opening in FrameShop

Image RemovedImage Added

Place a Guide

Info

  • Now we will place a Guide that we can use to align our V-Groove.

  • The V-Groove will be converted into our new Top Layer in Trace.

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

  • Click the checkbox for Add at Bottom.

  • Enter 1.5" for the Distance From Bottom field and click OK.

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Image RemovedImage Added

  • A Guide is placed at the Bottom of the design.

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Image RemovedImage Added
Info

  • Now we'll use the same steps to place a second Guide that we can use to align the CutArt.

  • Right-Click on the opening and select New Guide From Other.

  • Click the checkbox for Add at Bottom.

  • Enter 1" for the Distance From Bottom field and click OK.

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Image RemovedImage Added

  • The second Guide is placed.

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Image RemovedImage Added

Place a V-Groove

Info

  • Now we will place a V-Groove around the opening. This will eventually be our new Top Layer.

  • Make sure that the Opening is selected.

  • Click on the Openings tab.   

  • Click the Add V-Groove button. 

  • Enter 1" for the Offset value and click OK.

Expand
titleV-Groove Definition

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

BevelType45VGSelect70800.jpg

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Expand
titleOffset Definition

The Offset button creates a displacement copy of the selected object a parallel distance away as specified in the Offset Revealfield.

See: Offset Function in Trace

Offset Rules in Trace:

Enclosed Objects:

  • The Left < button will offset an enclosed object to the outside.

  • The Right > button will offset an enclosed object to the inside.

Arcs and Curves greater than 180 Degrees use the same rules as closed objects. 

Unenclosed Objects:

For unenclosed objects the arrow buttons depend on the direction of travel of the vector segments, starting from the line’s start point. The Left < button offsets Clockwise and Right > button offsets Counter-Clockwise.

If it doesn’t Offset in the expected direction, click Undo and click the other Offset Direction.

Info

  • The V-Groove is placed.

  • Click on the V-Groove to resize it.

Expand
titleV-Groove Definition

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

BevelType45VGSelect70800.jpg

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

  • Pull down the Bottom of the V-Groove and let it snap to the bottom Horizontal Guideline that we placed. Make sure you are pulling the V-Groove down and not just moving it.

  • Release the mouse to place it.

Expand
titleV-Groove Definition

The Normal Bevel Closed V-Groove involves two symmetrical cuts: one in the matboard and a corresponding cut in the fallout, both forming a mirrored arrangement. The matboard is sliced halfway through the thickness and the core is visible from the front.

First Cut: Cuts the Interior cut into the Fallout Clockwise.

Second Cut: Cuts the Exterior cut into the Matboard Counter-Clockwise.

Select V-Groove from the Current Bevel Type dropdown control to edit this configuration.

BevelType45VGSelect70800.jpg

See: 45 Degree Closed V-Groove Configurations

See: 45 Degree Plus Closed V-Groove Configurations

See: 45 Front Closed V-Groove Configurations

See: 52 Degree Closed V-Groove Configurations

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Place CutArt on Design

Expand
titleCutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function

  • Navigate to the desired location.

  • Click on the desired CutArt and click Select.

Expand
titleCutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function

  • The CutArt is placed.

  • Move the CutArt down to the Top Guide we placed and Center it Horizontally.

    • You may need to Zoom In to make the placement easier.

Expand
titleCutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function

Expand
titleGuide Definition

A Guide is a Red line marker which can direct the motion or positioning of objects.

The sides and centers of Objectscan snap to the Guide Lines.

Click on the Ruler around the design and drag toward the center to place a Guide.

Select the Guide and click Properties to edit the position or drag it where desired.

See: Guide Lines Properties

Image RemovedImage Added

Bring Design into Trace

Image RemovedImage Added

Add a Layer

Info

  • We're going to add a Layer to the Design for our new Top Layer.

  • Click on the Set Bevels tab.

  • Click Add in the Layers section.

  • A new Layer will be added. You can see by the muted design that nothing is currently Traced on this layer.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

Trace the Design

Info
Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

  • Select the Outside Object which will be our new Top Layer.

Info

  • We're going to Retrace the CutArt and the other opening onto a different Layer which will move them from this Layer.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

  • Click the CutArt to select it.

  • Click the Cartridge Type desired, such as the Penor Deboss Setbutton. 

Info

  • The CutArt will turn the color of the selected Cartridge.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

Expand
titleCartridge Definition

A Cartridge is the physical component that holds the Blade, Deboss Stylus, Pen or other application tool.

  • Click on the Middle Mayer object.

  • Click the 45° Bevel Set button to Trace it. It will turn Blue.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

  • Click on the Bottom Layer object.

  • Click on the 45° Bevel Set button to Trace it. It will turn Blue.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

  • You can click on each layer on the Layer List and make sure everything is Traced onto the correct layer. 

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

Expand
titleBevel Type Definition

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Save, Cut

Info

  • The CutArt on lower layer design is completed.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply with a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

See: Tracing the Design

Expand
titleCutArt Definition

CutArt™ are simple shapes and design elements created by Wizard that can be added to designs.

CutArts can be applied to your current design and edited, such as resizing and rotating.

They can be Cut, Debossed, Penned or cut on Vinyl.

See: Add CutArt Function

Image RemovedImage Added

Comparison

You can see how much we changed the design when you compare it to the original version. You can also run through these same steps to place a LetterMat, TTF, Deboss, Pen or Crease item or other object onto a layer other than the top layer. 

Image RemovedImage AddedImage RemovedImage Added