Content Comparison

• Crease Exterior If the Backup is cut Too Long.

The Exterior Backup controls where the Blade Plunges into the Blade Plunges into the Matboard(not the Fallout) on the Exterior cutcuts of Openings. 

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

If the Exterior Backup is cut too Short, it can leave a Hook in the cornerToo Long, Decrease the Backup.

If the Exterior Backup is cut too LongToo Short, Decrease Increase the Exterior Backup.If the Exterior

The Backup is cut too Short, Increase the Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image AddedImage Added

See: Backup for Creases.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Crease Exterior If the Backup is cut Too Short.

The Exterior Backup controls where the Blade Plunges into the Blade Plunges into the Matboard(not the Fallout) on the Exterior cut. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.cuts of Openings. 

If the Exterior Backup is cut too Short, it can leave a Hook in the cornerToo Long, Decrease the Backup.

If the Exterior Backup is cut too LongToo Short, Decrease Increase the Exterior Backup.If the Exterior

The Backup is cut too Short, Increase the Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image AddedImage Added

See: Backup for Creases.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Crease Exterior If the Overcut is cut Too Long.

The Exterior Overcut controls where the Blade Retracts the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

If the Overcut is cut Too Long, Decrease the Overcut.The

Exterior If the Overcut is cut Too Short, Increase the Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior OvercutImage AddedImage Added

See: Overcut for Creases.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Crease Exterior If the Overcut is cut Too Short.

The Exterior Overcut controls where the Blade Retracts the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

If the Overcut is cut Too Long, Decrease the Overcut.The

Exterior If the Overcut is cut Too Short, Increase the Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior OvercutImage AddedImage Added

See: Overcut for Creases.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Crease is applied at the Wrong Size.

The Opening Adjustment controls the size of the Object Opening cut or Object applied with non-blade cartridges.

If the Opening Crease is cut too Too Large, Decrease the Opening Adjustment.

If the Opening Crease is cut too Too Small, Increase the Opening Adjustment.

Image Added

Image Added

See: Opening Adjustment for Creases.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Crease is applied at the Wrong Depth When Using a SKU.

The Depth Bias is used to calculate the properBlade Depth when the SKUselected for the matboard contains the Matboard Thickness.

If the Blade Depth is cut Too Deep, Decrease the Depth Bias.

If the Blade Depth is cut Too Shallow, Increase the Depth Bias.

The formula is: [(Default Depth) - 10]

For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the the Depth Bias.

Image Added

See: Depth Bias.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Select this topic to see information on editing with the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Added

Set up the Box Defaults for the Crease cartridge in the Admin Editor section of the software.

Image Modified