Page Comparison

The Outside Rotation on Non-Oval V-Grooves controls for Swoops and Flares in the Outside Cut of the Non-Oval V-Grooves.

A Swoopin a Non-Oval V-Groove is where the corners Curve Inward toward the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Swoop, Decrease the Outside Rotation.

A Flare in a Non-Oval V-Groove is where the corners Curve Away from the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Flare, Increase the Outside Rotation.

Select desired Cartridge Tab. 

Select the desired Bevel Type from Current Bevel Type.

Edit the desired Configuration field.

Edit the Inside Rotation or Outside Rotation field, depending on which V-Groove line you are editing.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Outside cut of the Non-Oval V-Groove has Swoops.

• Decrease the Outside Rotation.

A Swoopin a Non-Oval V-Groove is where the corners Curve Inward toward the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Swoop, Decrease the Outside Rotation.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Outside cut of the Non-Oval V-Groove has Flares.

• Increase the Outside Rotation.

A Flare in a Non-Oval V-Groove is where the corners Curve Away from the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Flare, Increase the Outside Rotation.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Outside Non-Oval V-Groove has a Swoop or Flare.

• Use the Troubleshooting Configurations to fine-tune for Swoop/Flare in a Non-Oval V-Groove.

The Outside Rotation on Non-Oval V-Grooves controls for Swoops and Flares in the Outside Cut of the Non-Oval V-Grooves.

A Swoopin a Non-Oval V-Groove is where the corners Curve Inward toward the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Swoop, Decrease the Outside Rotation.

A Flare in a Non-Oval V-Groove is where the corners Curve Away from the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Flare, Increase the Outside Rotation.