Versions Compared

Version Old Version 31 New Version 32
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Info

Note: Not all cartridges are available for all CMC models.

Image Modified

Crease Cartridge Configurations

Info

  • The Crease Cartridge creases the material to make folding it easier when making Boxes.

Expand
titleCartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Image Modified

Crease Tab

  • Select the Deboss Tab on the Configurations screen. 

  • Select the Crease Cartridge.

Tip

  • Crease Cartridge

Image Modified

Crease Exterior Backup is too Long

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Crease Exterior Backup is Too Long.

  • This is viewed from the front of the mat.

Resolution:

If the Exterior Backup is cut

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Backup Definition

The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cut. 

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

If the Exterior Backup is cut too Short, it can leave a Hook in the corner.

If the Exterior Backup is cut too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut too Short, Increase the Exterior Backup.

Image Modified

Crease Exterior Backup is too Short

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Crease Exterior Backup is Too Short.

  • This is viewed from the front of the mat.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Backup Definition

The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cut. 

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

If the Exterior Backup is cut too Short, it can leave a Hook in the corner.

If the Exterior Backup is cut too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut too Short, Increase the Exterior Backup.

Image Modified

Crease Exterior Overcut is too Long

Problem:

The Crease Exterior Overcut
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Crease Exterior Overcut is applied Too Long.

  • This is viewed from the front of the mat.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Image Modified

Crease Exterior Overcut is too Short

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Crease Exterior Overcut is applied Too Short.

  • This is viewed from the front of the mat.

Resolution:

If the Exterior
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Image Modified

Crease is the Wrong Size

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Crease is applied at the Wrong Size.

  • This is viewed from the front of the mat.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleOpening Adjustment Definition

The Opening Adjustment controls the size of the Object cut or applied with non-blade cartridges.

If the Opening is cut too Large, Decrease the Opening Adjustment.

If the Opening is cut too Small, Increase the Opening Adjustment.

Image Modified

Crease is Applied at the Wrong Depth When Using a SKU

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Crease is applied at the Wrong Depth When Using a SKU.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • The Blade Depth is too Deep, Decrease the Depth Bias.

  • The Blade Depth is too Shallow, Increase the Depth Bias.

  • See Depth Bias for additional information.

Expand
titleDepth Bias Definition

The Depth Bias is used to calculate the properBlade Depth when the SKUselected for the matboard contains the Matboard Thickness.

The formula is: [(Default Depth) - 10]

For example, if the normal Blade Depth for 4-ply is 11, then 11-10=1, so enter 1 for the Depth Bias.

Image Modified

Troubleshooting Button 

Info

  • Select this topic to see information on editing with the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

Image Modified

Set Box Defaults

Expand
titleDefault Settings for the Box Utility

Set up the Box Defaults for the Crease cartridge in the Admin Editor section of the software.

Image Modified