">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 42 Next »

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Deboss Wide Configurations

  • The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

  • This is viewed from the front of the mat.

 Cartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Select the Deboss Wide Cartridge Type

  • Select the Deboss Tab on the Configurations screen.  

  • Select the Wide-Blue cartridge from the Cartridge dropdown control.

  • Deboss Wide

Select the Area of Concern for Wide Deboss Below:

  • Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.

Deboss-Wide is Applied to the Wrong Place Horizontally

Problem:

  • Deboss-Wide is applied to the wrong place Horizontally.

    • This is viewed from the front of the mat.

Resolution:

 Horizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Left, Increase the Horizontal Adjustment.

If the Non-Blade Tool line is applied Too Far Right, Decrease the Horizontal Adjustment.

Deboss-Wide is Applied to the Wrong Place Vertically 

Problem:

  • Deboss-Wide is applied to the wrong place Vertically.

    • This is viewed from the front of the mat.

Resolution:

 Vertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Up, Decrease the Vertical Adjustment.

If the Non-Blade Tool line is applied Too Far Down, Increase the Vertical Adjustment.

Deboss-Wide is the Wrong Size

Problem:

  • Deboss-Wide is the Wrong Size.

    • This is viewed from the front of the mat.

Resolution:

 Opening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

Deboss-Wide Applied at the Wrong Depth

Problem:

  • Deboss-Wide is applied at the Wrong Depth.

    • This is viewed from the front of the mat.

Resolution:

 Depth Setting Definition

The Depth Setting controls the Blade Depth for the Non-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

Deboss-Wide Cartridge Tears the Mat 

Problem:

  • Deboss-Wide Cartridge Tears the Mat.

    • This is viewed from the front of the mat.

Resolution:

  • Non-Blade Tool is Tearing in the Corners of the segments:

  • Non-Blade Tool is Pausing Too Long in the Corners of the segments:

 Corner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.  

Deboss-Wide Lines are too Long

Problem:

  • Deboss-Wide Lines are Too Long.

    • This is viewed from the front of the mat.

Resolution:

  • Overshoot is too Long:

 Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

Deboss-Wide Lines are too Short 

Problem:

  • Deboss-Wide Lines are Too Short.

    • This is viewed from the front of the mat.

Resolution:

  • Overshoot is too Short:

 Overshoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

Deboss-Wide Set to Plunge Between Segments

Problem:

  • Deboss-Wide Set to Plunge Between Segments.

    • This is viewed from the front of the mat.

Resolution:

  • Non-Blade Tool leaves a Dot where it plunges:

    • Select Unplunge.

  • Non-Blade Tool takes Too Long to apply:

    • Select Plunge.

  • See Plunge for additional information.

 Plunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

Troubleshooting Button 

 Troubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

  • No labels