">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 20 Next »

  • The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

  • The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

 Interior Overcut General Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for Openings Configurations

See: Interior Overcut for Drops Configurations

See: Interior Overcut for the Outside Configurations

See: Interior Overcut for V-Grooves Configurations

 Interior Overcut on Openings Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for Openings Configurations

 Interior Overcut on Drops Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for Drops Configurations

 Interior Overcut on the Outside Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut is cut Too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: Interior Overcut for the Outside Configurations

 Interior Overcut of V-Grooves Definition

The V-Groove Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of the Inside Cut of the V-Groove.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).  

If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Long, Decrease the Interior Overcut on V-Grooves.

If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Short, Increase the Interior Overcut on V-Grooves.

The V-Groove Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

See: V-Groove Interior Overcut Configurations

 How to Adjust the Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

  • No labels