Cartridge Type Examples
The examples below display the different Cartridges that can be selected from the Cartridge Type Tabs.
The examples below display the different Cartridges that can be selected from the Cartridge Type Tabs.
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. Take note that there is a separate configuration for cutting from the front (Normal Bevel - Front of Mat) and cutting from the back (Normal Bevel). |
45 Degree Cartridge
The 45 Degree Cartridge cuts a 45° bevel into the matboard, and includes the following Bevel Types:
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle. |
Normal Bevel
Reverse Bevel
Normal Drop
Reverse Drop
Outside
Normal Bevel-Front of Mat
Reverse Bevel-Front of Mat
Normal Drop-Front of Mat,
Reverse Drop-Front of Mat
Outside-Front of Mat
V-Groove
45 Degree + Cartridge
The 45°+ Cartridge (45° Plus Cartridge) cuts a 45° bevel into thicker matboard such as 8-ply, and includes the following Bevel Types:
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle. |
Normal Bevel
Reverse Bevel
Normal Drop
Reverse Drop
Outside
Normal Bevel-Front of Mat
Reverse Bevel-Front of Mat
Normal Drop-Front of Mat,
Reverse Drop-Front of Mat
Outside-Front of Mat
V-Groove
45 Degree Front Cartridge
The 45° Front Cartridge cuts a 45° bevel into the matboard from the front, and includes the following Bevel Types:
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle. |
Normal Bevel-Front of Mat
Reverse Bevel-Front of Mat
Normal Drop-Front of Mat,
Reverse Drop-Front of Mat
Outside-Front of Mat
V-Groove
52 Degree Cartridge
The 52 Degree Cartridge cuts a 52° bevel into the matboard, and includes the following Bevel Types:
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle. |
Normal Bevel
Reverse Bevel
Normal Drop
Reverse Drop
Outside
Normal Bevel-Front of Mat
Reverse Bevel-Front of Mat
Normal Drop-Front of Mat,
Reverse Drop-Front of Mat
Outside-Front of Mat
V-Groove
90 Degree Cartridge
The 90 Degree Cartridge cuts a 90° opening into the matboard, displaying no bevel, and includes the following Bevel Types:
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle. |
Normal Bevel
Normal Drop
Outside
Normal Bevel-Front of Mat
Normal Drop-Front of Mat,
Outside-Front of Mat
Deboss Cartridges
The Deboss Cartridges press into the matboard to create a subtle design. It is applied to the front* of the mat, and anything else on that layer will also be cut from the front.
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Deboss cartridge stylus presses onto the surface of the matboard to create a subtle design. There are three Deboss stylus sizes: Wide, Medium, Thin. In addition to Templates, you can also Deboss CutArts, LetterMats and TTFs. |
It includes the following Tool Cartridges:
Wide - Blue
Medium - Red
Thin - White
Pen Cartridge
The Pen Cartridge holds a pen to the matboard to draw lines or other objects onto the matboard. It is applied to the front* of the mat, and anything else on that layer will also be cut from the front.
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Pen Cartridge is used to draw onto the surface of the matboard on the CMC to create a design. In addition, you can also Pen Designs, CutArts, LetterMats and TTFs. |
You can have up to nine different pens defined, and each pen has a separate set of configurations. It includes the following Tool Cartridges:
1-Pen
2-Pen
3-Pen
4-Pen
5-Pen
6-Pen
7-Pen
8-Pen
9-Pen
Vinyl Cartridge
The Vinyl Cartridge cuts designs into sheets of Vinyl which have been temporarily adhered to the matboard. It is cut from the front* of the mat, and anything else on that layer will also be cut from the front.
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Vinyl Cartridge uses a special blade to cut the Vinyl which has been temporarily adhered to matboard to create the design. |
Crease Cartridge
The Crease Cartridge perforates the material to make folding it easier when making Boxes. It is applied to the front* of the mat, and anything else on that layer will also be cut from the front.
A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool. |
The Crease Cartridge is used to apply Crease marks that are used to assist in folding the thicker finished Box. |
*Cut From Front can either be selected on the Cutting Preview or set in the Admin > Cutting > Cut From Front section of the software, or will be automatically selected if there is a cut-from-front element on the current layer being cut, such as a Deboss or V-Groove. This will force it to cut all openings on that layer from the front.
