The Overcut controls where the Blade Retracts from the Matboard/Fallout on the Exterior cuts. The initial plunge position is determined by the bevel type. The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.  See: Exterior Overcut for Openings Configurations See: Exterior Overcut for Drops Configurations See: Exterior Overcut for the Outside Configurations The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of the Outside Cut of the Non-Oval V-Groove. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut. The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. The Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Overcut is cut Too Long, Decrease the Exterior Overcut. If the Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration. The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. See: Interior Overcut for Openings Configurations See: Interior Overcut for Drops Configurations The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. The V-Groove Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of the Inside Cut of the V-Groove. The initial plunge position is determined by the bevel type. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Long, Decrease the Interior Overcut on V-Grooves. If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Short, Increase the Interior Overcut on V-Grooves. The V-Groove Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration. | |