">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 14 Next »

Cut the Outside On  

Use the Cut the Outside toggle to select cutting or not cutting the outside of the mat for the CMC Z1, Z (9000z), 9000, and 8000.

  • Click the Cut Outside toggle On to cut the outside of the mat.

  • The outside of the mat will now cut. 

Note: You can also select Options > Cut Outside.

Cut the Outside Off

  • Click the Cut Outside toggle Off to not cut the outside of the mat.

  • The outside of the mat will not be cut.

Set Advanced Options: Enable Outside Cut

Defaults: Set the Default for Cutting the Outside 

 Default Settings for Cutting the Outside

The default setting for Cutting the Outside can be set in the Admin > Editor section for the CMC Z1, Z (9000z), 9000 and 8000.

Defaults: Set the Default for 90 Degree Outside Cut

 Default Settings for Cutting the Outside with the 90 Degree Cartridge

The default setting for 90 Outside Cuts can be set in the Admin > Cutting section for the CMC Z1, Z (9000z) and 9000.

Note that the CMC 8000 does support cutting with the 90 Degree Cartridge.

Enable Auto Clamp Offset

  • Select Enable Auto Clamp Offset checkbox to move the design up and over on the matboard to avoid the clamp area on the CMC Z1 and Z (9000z), similar to the Rail Dodge below.

 Enable Auto Clamp Definition

The Auto Clamp Offset moves the design up and over on the matboard to avoid the clamp area on the CMC Z1 and Z (9000z) to overcome the border limitation of 1.25"/3.2 cm when not cutting the outside.

  • Check the Enable Auto Clamp Offset checkbox.  

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y position and it will display Dodge on the bottom of the screen on the CMC Z1 and Z (9000z).

  • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Disable Auto Clamp Offset

  • Disabling the Auto Clamp Offset will cut the design normally without being offset an extra distance into the mat on the CMC Z1 and Z (9000z).

 Enable Auto Clamp Definition

The Auto Clamp Offset moves the design up and over on the matboard to avoid the clamp area on the CMC Z1 and Z (9000z) to overcome the border limitation of 1.25"/3.2 cm when not cutting the outside.

  • Uncheck the Auto Clamp Offset checkbox.

  • The design will no longer be offset on the CMC Z1 and Z (9000z) and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

Defaults: Set the Default for the Enable Auto Clamp Offset

 Set the Default to Enable Auto Clamp Offset

The default setting and offset value for the Enable Auto Clamp Offset for the CMC Z1 and Z (9000z) can be set in the Admin > Cutting section.

Enable Rail Dodge

 Rail Dodge Definition

A Rail Dodge moves the design up and over on the matboard to avoid the clamp area on the CMC 9000 and 8000 to overcome the border limitation of 1.5”/3.8cm when not cutting the outside.

  • Check the Enable Rail Dodge checkbox to use a Rail Dodge on CMC 9000 and 8000. This is similar to the Enable Auto Clamp Offset above.

  • A Rail Dodge is a small piece of matboard or other material used to position the pre-cut matboard up into the cutting area when using borders less than 1.5" and not cutting the outside.

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same number value. 

  • It will move the lower left corner of the design to the new X/Y position and it will display Dodge on the bottom of the screen.

Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

See Also: Fixture for Rail Dodge.  

Disable Rail Dodge

  • Disabling the Rail Dodge will now cut the designs normally without being offset up and over on the mat.

 Rail Dodge Definition

A Rail Dodge moves the design up and over on the matboard to avoid the clamp area on the CMC 9000 and 8000 to overcome the border limitation of 1.5”/3.8cm when not cutting the outside.

  • Uncheck the Rail Dodge checkbox.

  • The design will no longer be offset on the CMC 8000 and 9000 and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above

Defaults: Set the Default for the Rail Dodge

 Default Setting for Rail Dodge

The default setting and offset value for the Rail Dodge can be set in the Admin > Cutting section.

See Also: Edit Menu: Cut Outside

Optionally, you can use the Edit menu to cut the outside of the design.

  • Click on the design to select it.

  • Click Edit > Cut Outside to cut the outside of the mat.

  • It will now cut the outside of the mat.

  • No labels