Using the Backup and Overcut Display on the Cut Preview for Troubleshooting | |
|---|---|
Cutting from the Front will cut with the face of the mat toward the operator, and can be selected on the Cut Preview.
If you are cutting an element that must be applied to the front of the mat, such as a V-Groove or Pen design, any openings on that layer will also cut from the front and use the Front of Mat configuration item; i.e., Normal Bevel-Front of Mat. So if you are having problems with a Normal Bevel cut on the same layer as a V-Groove, make sure you select Normal Bevel-Front of Mat to edit the configurations for that opening. The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior Cuts of Openings. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup. If the Exterior Backup is cut Too Long, Decrease the Exterior Backup. If the Exterior Backup is cut Too Short, Increase the Exterior Backup. The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration. See: Exterior Backup for Openings Configurations See: Exterior Backup for Drops Configurations See: Exterior Backup for the Outside Configurations The V-Groove Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cuts of the Outside Cut of the V-Groove. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Backup on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Backup. If the Exterior Backup on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Backup. The V-Groove Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut. The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. See: Exterior Overcut for Openings Configurations See: Exterior Overcut for Drops Configurations See: Exterior Overcut for the Outside Configurations The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of the Outside Cut of the Non-Oval V-Groove. The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout). If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Overcut. If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut. The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Backup is cut Too Long, Decrease the Interior Backup. If the Interior Backup is cut Too Short, Increase the Interior Backup. The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. See: Interior Backup for Openings Configurations See: Interior Backup for Drops Configurations The V-Groove Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts on the Inside Cut of the V-Groove. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Backup on the Inside Cut of the V-Groove is cut Too Long, Decrease the Interior Backup. If the Interior Backup on the Inside Cut of the V-Groove is cut Too Short, Increase the Interior Backup. The V-Groove Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut is cut Too Long, Decrease the Interior Overcut. If the Interior Overcut is cut Too Short, Increase the Interior Overcut. The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. See: Interior Overcut for Openings Configurations See: Interior Overcut for Drops Configurations The V-Groove Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of the Inside Cut of the V-Groove. The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard). If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Long, Decrease the Interior Overcut on V-Grooves. If the Interior Overcut on the Inside Cut of the V-Groove is cut Too Short, Increase the Interior Overcut on V-Grooves. The V-Groove Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map/wiki/spaces/FrameShop8x/pages/1942503207illustration. |    |