Versions Compared

Old Version 24

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version Current

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

View file
nameUpgradeTerminationReturn-FullBoard80002024-0506-2407.pdf

Please box up the following four items for return

Please use your original CMC box to box up the following four items into one box.

If you do not have your original packaging the box the new CMC arrived in can be used.
• Board
• Gantry
• Head
• ECU/Driver Pack
Please see the following removal instructions for each part.

Head Removal

Warning

Caution: Head appearance may vary from model shown, but the connections are the same. Do not pick up head Head using the blade depth knob or the head Head cover. Pick up the head Head by holding the “D-Shaped” upper and lower head Head plates.

  • If the motors are engaged, click reset motors button Reset Motors Button on the cut preview Cut Preview and click OK on the release motors prompt.

  • Press the 0 on the rocker switch on the back of the ECU to turn off the ECU.

  • Push blade cartridge release down to eject the blade cartridge. Turn off the air.

  • Remove the two gantry Gantry covers by unscrewing the screws that hold them in place and set them aside.

  • Move the gantry Gantry to the right side of the board Board until the Footblock is off of the boardBoard.

  • Remove the two 5/32” screws and set aside.

RemoveHeadScrewsZ98k2024800.png

  • If present, remove the Head Assembly Power Cable Strain Relief from around the base sides of the Head Power Plug connection.

PowerCableStrainReliefOffZ98k2024800.png

  • Disconnect the head Head power plug (square connection) from the head Head grabber arm.

HeadPowerConnect8000OffNoRetainer800.png

  • Disconnect the air to the head Head by untwisting the two air fittings.

HeadAirLinesConnect8000OffNoRetainer800.png

  • Roll the head Head down the gantry Gantry until it rolls off the gantryGantry, taking care not to drop it.

  • Replace the two 5/32” screws into the headHead.

Removing the ECU/Driver Pack

  • Make sure the rocker switch on the back of the ECU is on the 0 for off.

  • Unplug the power cord.

  • Disconnect the male end of the board Board cable from the back of the ECU by turning the locking ring and pulling gently.

  • Unplug the USB Cable from the back of the ECU/Driver Pack.

Secure the Gantry: Loosening Drive Belt

  • Move the gantry Gantry to the right side of the board Board about two feet from the right edge (to leave room for the packaging foam corners).

  • Remove the 5/32” Allen screws and washers from the lower gantry Gantry plate.

  • Locate the 3/16” Allen belt tensioner screw that’s located on the right bottom side of the lower rail and marked with a red dot.

  • Loosen this screw one turn only.

Warning

WARNING: Make sure you do not over-loosen this screw. One full turn is usually sufficient.

  • There should be some movement in the belt tensioner. The tensioner springs should be visible.

  • Locate the belt tensioner hole on the end of the belt tensioner. Place the 5/32” Allen screw and washer we removed from the lower gantry Gantry plate into the belt tensioner hole. Tighten the Allen screw until belt tensioner is flush with the rail and the springs are not visible.

  • Go back and tighten the 3/16” Allen belt tensioner screw.

  • Lift the drive belt Drive Belt from the rail. Pushing the drive belt Drive Belt end to the right may assist in getting a hold of it.

  • Wind up the drive beltDrive Belt, and rubber-band rubberband it.

  • Repeat steps 4 through 8 with the upper rail.

Secure the Gantry: Remove Stop Plate

  • Move the gantry Gantry far enough to the left to dislodge the belt anchors. The belt anchors are sunk into the left ends of the rails and are attached to the drive beltsDrive Belts.

  • See the instructions following for the type of Gantry Stop your machine has.

Magnetic Stop

  • Loosen the top 3/16” stop screw Stop Screw of the Magnetic Gantry Stop.

  • Lift up the magnetic stop plate Magnetic Gantry Stop to disengage the pin from the hole and slide the alignment plate to the left end of the rail to remove.

Silver Gantry Stop Plate

  • Remove the right front 3/16” stop screw Stop Screw of the silver Gantry Stop Plate and set aside.

  • Loosen the back left T-Nut screw and slide the alignment plate Gantry Stop Plate to the left end of the rail to remove.

Stop Screw

  • If your model only has a Stop Screw without the alignment plate, remove the stop screwStop Screw.

Attaching Shipping Blocks

  • If the shipping blocks have been misplaced, please find a way to secure the gantry Gantry so that it does not move during shipment.

  • Loosely place the T-Nut onto the shipping blocks and slide onto the rail on each side of the gantryGantry. The left one is placed on the underside of the rail, and the right one is placed on the top of the rail.

  • Tighten into place.

  • Place the other two shipping blocks on the lower rail. They will be placed on the top of the bottom rail. Tighten into place.

...

Magnetic Gantry Stop

  • Slide the black Magnetic Gantry Stop Plate in from the left end of the rail keeping the pin towards you.

  • Place the pin into the hole and tighten the top 3/16” stop screwStop Screw.

Silver Gantry Stop Plate

  • Slide the alignment plate Gantry Stop Plate in from the left end of the rail and line up with the holes on the rail.

  • Tighten the back left T-Nut screw. Replace the right front 3/16” stop screw Stop Screw and tighten.

Stop Screw

  • If your model only has a Stop Screw without the alignment plate, replace the stop screwStop Screw.

Installing the Drive Belt onto the Rail

  • Lightly pull the coiled drive belt Drive Belt toward the right to take up the slack and pull the belt anchor into place flush with the end of the CMC.

  • Remove the rubber-band rubberband from the drive belt Drive Belt and loosely lay the drive belt Drive Belt along the rail channel.

  • Pull the loose belt end to the right, making sure that the drive belt Drive Belt is not twisted and that the teeth are facing down toward the board Board into the rail channel. Slide the screw of the belt end into the belt tensioner slot.

  • Remove the 5/32” Allen screws and washers from the belt tensioner.

  • Place the two Allen screw and washer into the holes provided on the lower gantry Gantry plate. Place them so that the screw protrudes only slightly from the back of the plate.

  • Loosen one full turn only the 3/16” Allen belt tensioner screw from the right bottom side of the lower rail marked with a red dot.

  • The belt tensioner should spring fully into place.

Warning

WARNING: Make sure you do not over-loosen this screw. One full turn is usually sufficient.

  • Snugly tighten the Allen belt tensioner screw on the bottom right of upper and lower rails.

  • Repeat these steps through with the upper rail.

BeltTensionerZTighteningBottom800.png

  • Replace the two gantry Gantry covers using the two screws removed earlier.

Packing up the Head

  • Place the packaging foam in the bottom of the box with the cradle toward the center.

  • Place the head Head upside down into the cradle; you may need to rotate the Footblock.

  • Place the remaining portion of the head Head packaging foam across the bottom of the head Head and around each side; press into place.

  • Close and tape up the box.

...

Boxing up the Board

  • Place the board Board box onto a table or other flat surface. Carefully place the foam corners onto the boardBoard.

  • With the help of a second person, carefully lift the board Board straight up and place it into the box.

  • Place the head Head box and the ECU box between the gantry Gantry and the side of the box between the foam corners.

  • Secure the board Board in place with additional packing material if needed.

  • Secure the box closed with banding or packing tape. The system is now ready to ship.

Return the Parts

  • Please use the return labels that have been provided. The head Head and gantry Gantry are shipped in the gantry Gantry box and the ECU is shipped in the ECU box.

  • Give the packages to your regular Fed-Ex delivery pickup.

  • If you do not have regular Fed-Ex delivery, call 1-800-GOFEDEX (1-800-463-3339) to arrange pickup.

  • If you have any questions, please contact Christina.Costilla@wizardcutters.com 425-551-4300 x4304.