Page Comparison

If the motors are engaged, click

Reset Motors Button on the

Cut Preview and click OK on the release motors prompt.

Press the 0 on the rocker switch on the back of the ECU to turn off the ECU.

Push blade cartridge release down to eject the blade cartridge. Turn off the air.

Remove the two

Gantry covers by unscrewing the screws that hold them in place and set them aside.

Move the

Gantry to the right side of the

Board until the Footblock is off of the

Board.

Remove the two 5/32” screws and set aside.

If present, remove the Head Assembly Power Cable Strain Relief from around the base sides of the Head Power Plug connection.

Disconnect the

Head power plug (square connection) from the

Head grabber arm.

Disconnect the air to the

Head by untwisting the two air fittings.

Roll the

Head down the

Gantry until it rolls off the

Gantry, taking care not to drop it.

Replace the two 5/32” screws into the

Head.

Make sure the rocker switch on the back of the ECU is on the 0 for off.

Unplug the power cord.

Disconnect the male end of the

Board cable from the back of the ECU by turning the locking ring and pulling gently.

Unplug the USB Cable from the back of the ECU/Driver Pack.

Move the

Gantry to the right side of the

Board about two feet from the right edge (to leave room for the packaging foam corners).

Remove the 5/32” Allen screws and washers from the lower

Gantry plate.

Locate the 3/16” Allen belt tensioner screw that’s located on the right bottom side of the lower rail and marked with a red dot.

Loosen this screw one turn only.

There should be some movement in the belt tensioner. The tensioner springs should be visible.

Locate the belt tensioner hole on the end of the belt tensioner. Place the 5/32” Allen screw and washer we removed from the lower

Gantry plate into the belt tensioner hole. Tighten the Allen screw until belt tensioner is flush with the rail and the springs are not visible.

Go back and tighten the 3/16” Allen belt tensioner screw.

Lift the

Drive Belt from the rail. Pushing the

Drive Belt end to the right may assist in getting a hold of it.

Wind up the

Drive Belt, and

rubberband it.

Repeat steps 4 through 8 with the upper rail.

Move the

Gantry far enough to the left to dislodge the belt anchors. The belt anchors are sunk into the left ends of the rails and are attached to the

Drive Belts.

See the instructions following for the type of Gantry Stop your machine has.

Loosen the top 3/16”

Stop Screw of the Magnetic Gantry Stop.

Lift up the

Magnetic Gantry Stop to disengage the pin from the hole and slide the alignment plate to the left end of the rail to remove.

Remove the right front 3/16”

Stop Screw of the silver Gantry Stop Plate and set aside.

Loosen the back left T-Nut screw and slide the

Gantry Stop Plate to the left end of the rail to remove.

If your model only has a Stop Screw without the alignment plate, remove the

Stop Screw.

If the shipping blocks have been misplaced, please find a way to secure the

Gantry so that it does not move during shipment.

Loosely place the T-Nut onto the shipping blocks and slide onto the rail on each side of the

Gantry. The left one is placed on the underside of the rail, and the right one is placed on the top of the rail.

Tighten into place.

Place the other two shipping blocks on the lower rail. They will be placed on the top of the bottom rail. Tighten into place.

Reinstall your Gantry Stop as described below.

Slide the black Magnetic Gantry Stop Plate in from the left end of the rail keeping the pin towards you.

Place the pin into the hole and tighten the top 3/16”

Stop Screw.

Slide the

Gantry Stop Plate in from the left end of the rail and line up with the holes on the rail.

Tighten the back left T-Nut screw. Replace the right front 3/16”

Stop Screw and tighten.

If your model only has a Stop Screw without the alignment plate, replace the

Stop Screw.

Lightly pull the coiled

Drive Belt toward the right to take up the slack and pull the belt anchor into place flush with the end of the CMC.

Remove the

rubberband from the

Drive Belt and loosely lay the

Drive Belt along the rail channel.

Pull the loose belt end to the right, making sure that the

Drive Belt is not twisted and that the teeth are facing down toward the

Board into the rail channel. Slide the screw of the belt end into the belt tensioner slot.

Remove the 5/32” Allen screws and washers from the belt tensioner.

Place the two Allen screw and washer into the holes provided on the lower

Gantry plate. Place them so that the screw protrudes only slightly from the back of the plate.

Loosen one full turn only the 3/16” Allen belt tensioner screw from the right bottom side of the lower rail marked with a red dot.

The belt tensioner should spring fully into place.

Snugly tighten the Allen belt tensioner screw on the bottom right of upper and lower rails.

Repeat these steps through with the upper rail.

Replace the two

Gantry covers using the two screws removed earlier.

Place the packaging foam in the bottom of the box with the cradle toward the center.

Place the

Head upside down into the cradle; you may need to rotate the Footblock.

Place the remaining portion of the

Head packaging foam across the bottom of the

Head and around each side; press into place.

Close and tape up the box.

Locate the packaging foam and fold out the interior feet.

Place the packaging foam on each end of the ECU/Driver Pack.

Place the ECU/Driver Pack carefully into the ECU/Driver Pack box.

Place all of the ECU/Driver Pack and emergency stop cables (if applicable) into the free space and tape shut.

Place the

Board box onto a table or other flat surface. Carefully place the foam corners onto the

Board.

With the help of a second person, carefully lift the

Board straight up and place it into the box.

Place the

Head box and the ECU box between the

Gantry and the side of the box between the foam corners.

Secure the

Board in place with additional packing material if needed.

Secure the box closed with banding or packing tape. The system is now ready to ship.

Please use the return labels that have been provided. The

Head and

Gantry are shipped in the

Gantry box and the ECU is shipped in the ECU box.

Give the packages to your regular Fed-Ex delivery pickup.

If you do not have regular Fed-Ex delivery, call 1-800-GOFEDEX (1-800-463-3339) to arrange pickup.

If you have any questions, please contact Christina.Costilla@wizardcutters.com 425-551-4300 x4304.