Versions Compared

Version Old Version 12 New Version Current
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
DefinitionThe Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image RemovedImage Removed

See: Overshoot for Pen Configurations

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).If the Overshoot of the Non-Blade Tool is applied OvershootArrows70800.pngImage AddedOvershootDebossMedium70800.pngImage Added

Overshoot

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl).

If the Overshoot is applied Too Long, Decrease the Overshoot.

If the Overshoot is applied Too Short, Increase the Overshoot.

Panel
panelIconIdatlassian-plus1f9d9-200d-2640-fe0f
panelIcon:pluswoman_mage:
panelIconText:plus:🧙‍♀️
bgColor#FFFAE6

  • The Overshootcontrols how far past the end of the Line/Arc Segment to apply the Non-Blade Tool(Deboss, Pen or Vinyl) adjusts the Non-Blade Cartridge’s Withdrawal from the Matboard.

    • If the Overshoot is applied Too Long, Decrease the Overshoot.

    • If the Overshoot is applied Too Short, Increase the Overshoot.

Expand
titleOvershoot General Definition
Expand
titleOvershoot General Definition

This is similar to the Overcut used with the Blade cartridges.

Image RemovedImage Removed

See: Overshoot for Deboss Configurations

See: Overshoot for Pen Configurations

See: Overshoot for Vinyl Configurations

Expand
titleDeboss Overshoot Definition

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

Image RemovedImage Removed

See: Overshoot for Deboss Configurations

Expand
titlePen Overshoot Definition
Expand
titleVinyl Overshoot Definition
Insert excerpt
How to Adjust the Configurations
How to Adjust the Configurations
nameHow to Adjust Configurations
nopaneltrue

Excerpt
hiddentrue
nameOvershoot

  • The Overshoot adjusts the Non-Blade Cartridge’s Withdrawal from the Matboard.

    • If Overshoot is Too Long, Decrease the Overshoot.

    • If

...

    • Overshoot

...

    • is

...

Expand
titleHow to Adjust the Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

...

    • Too Short, Increase the Overshoot.

This is similar to the Overcut used with the Blade cartridges.

...

See: Overshoot for Vinyl Configurations

Image Added

Full Definition: Overshoot Definition