Content Comparison

• The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

• The Exterior Cuts is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

  • If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

  • If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for Openings Configurations

See: Exterior Overcut for Drops Configurations

See: Exterior Overcut for the Outside Configurations

See: Exterior Overcut for V-Grooves Configurations

See: Exterior Overcut for Creases Configurations

The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for Openings Configurations

The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for Drops Configurations

The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Exterior Overcut for the Outside Configurations

The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard(not the Fallout)on the Exterior cuts of the Outside Cut of the Non-Oval V-Groove.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decreasethe Exterior Overcut.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: V-Groove Exterior Overcut Configurations

The Overcut controls where the cartridgeRetracts from the Matboard.

If the Overcut is Too Long, Decrease the Exterior Overcut.

If the Overcut is Too Short, Increase the Exterior Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

See: Overcut for Creases Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.