Versions Compared

Old Version 26

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 27

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Troubleshooting the Backup/Overcut Display

  • Have a cut design displayed on the Cut Preview.

  • Note that this feature is only available for the Bladed Cartridges.

  • Using one of the Zoombuttons, zoom in to the desired section of the project where you are having issues cutting.

Image Modified

  • Make sure that the Green Backups and Red Overcuts lines are visible.

Expand
titleExterior Backup Definition

The Exterior Backup controls where the Blade Plunges into the Matboard on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).    

If the Exterior Backup is leaving a Hook in the corner, Increase the Exterior Backup.

If the Exterior Backup is cut Too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut Too Short, Increase the Exterior Backup.

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

Image ModifiedImage Modified

See: Exterior Backup for Openings Configurations

See: Exterior Backup for Drops Configurations

See: Exterior Backup for the Outside Configurations

See: Exterior Backup for V-Grooves Configurations

See: Exterior Backup for Creases Configurations

Expand
titleInterior Backup Definition

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).    

If the Interior Backup is cut Too Long, Decrease the Interior Backup.

If the Interior Backup is cut Too Short, Increase the Interior Backup.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration.

Image ModifiedImage Modified

See: Interior Backup for Openings Configurations

See: Interior Backup for Drops Configurations

See: Interior Backup for the Outside Configurations

See: Interior Backup for V-Grooves Configurations

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the BladeRetracts from the Matboard (not the Fallout) on the Exterior cuts of Openings. The initial plunge position is determined by the bevel type.

The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).    

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

Image ModifiedImage Modified

See: Exterior Overcut for Openings Configurations

See: Exterior Overcut for Drops Configurations

See: Exterior Overcut for the Outside Configurations

See: Exterior Overcut for V-Grooves Configurations

See: Exterior Overcut for Creases Configurations

Expand
titleInterior Overcut Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cuts of Openings. The initial plunge position is determined by the bevel type.

The Interior Cut is where the Blade Plunges or Retracts from the Fallout (not the Matboard).   

If the Interior Overcut is cut Too Long, Decreasethe Interior Overcut.

If the Interior Overcut is cut Too Short, Increase the Interior Overcut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Mapillustration.

Image ModifiedImage Modified

See: Interior Overcut for Openings Configurations

See: Interior Overcut for Drops Configurations

See: Interior Overcut for the Outside Configurations

See: Interior Overcut for V-Grooves Configurations

Image Modified

  • With the cursor hovering over one of the Backups or Overcuts, the Status Bar displays the actual physical length of the selected Backup or Overcut.

  • This value will be the Sum of the corresponding User Configuration setting and the Factory Configuration setting.

Image Modified

  • The cursor will turn into an arrow with a question mark.

  • Click on the desired Overcut or Backup line that you are having trouble with.

Tip
Image Modified

  • The Configuration screen will open to the appropriate Cartridge Tab with the Configuration Field associated to the line clicked highlighted.

  • Now you can easily adjust the value displayed, depending upon whether the item selected is cutting Too Short or cutting Too Long.

    • Increase the value if the item is cutting Too Short.

    • Decrease the value if the item is cutting Too Long.

  • Click OK and recut the design.

  • Continue adjusting the Configurations until you achieve the desired result.

Tip

  • To adjust, click Plus/Minus on the desired field about five times.

  • Click OK and do another test cut.

  • Continue making adjustments until the desired outcome is achieved.

Image Modified