Versions Compared

Old Version 58

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 59

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Rotation on Creases

  • If the Crease has a Swoop, Increase the Rotation.

  • If the Crease has a Flare, Decrease the Rotation.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Troubleshooting Utility for information on adjusting for a Swoop or Flare in a Non-Oval.

Expand
titleHow to Select the Bevel Type to Edit

Select desired Cartridge Tab. 

Select the desired Bevel Type from Current Bevel Type.

Edit the desired Configuration field.

Expand
titleHow to Adjust the Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Crease has a Swoop

  • If the Crease has a Swoop, Increase the Rotation.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Troubleshooting Utility for information on adjusting for a Swoop or Flare in a Non-Oval.

Expand
titleSwoop in Crease Definition

A Swoop in a Crease is where the corners Curve Inward toward the crease.

If the Crease has a Swoop, Increase the Rotation.

The Rotation controls for Swoops and Flares in Openings.

Expand
titleHow to Adjust the Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Crease has a Flare

  • If the Crease has a Flare, Decrease the Rotation.

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • For Additional Information: See Troubleshooting Utility for information on adjusting for a Swoop or Flare in a Non-Oval.

Expand
titleFlare in Crease Definition

A Flare in a Crease is where the corners Curve Away from the crease.

If the Crease has a Flare, Decrease the Rotation.

The Rotation controls for Swoops and Flares in Openings.

Expand
titleHow to Adjust the Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

  • If the Crease has a Swoop, Increase the Rotation.

  • If the Crease has a Flare, Decrease the Rotation.

    • Use the Troubleshooting Configurations to fine-tune for Swoops/Flares in a Crease

    Troubleshooting Utility for Openings

    Panel
    panelIconId1f9d9-200d-2642-fe0f
    panelIcon:man_mage:
    panelIconText🧙‍♂️
    bgColor#FFFAE6

    • For Additional Information: See Troubleshooting Utility for information on adjusting for a Swoop or Flare in a Non-Oval.