Versions Compared

Old Version 14

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 15

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Line Design Details

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Click on a Line to see the specific details about it. 

Expand
titleLine Tool Definition

The Line tool in Trace will draw a Two-Point Line. 

The Line is defined by two points: the Initial Position and the Terminating Position (which are called “anchors”).

After it is drawn, a third point in the Center is displayed, which can be moved to alter the Line into an Arc.

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • The Design Details section displays information about the selected line.

Image RemovedImage Added

Design Line Details

Start X and Start Y

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • Displays the Start X/Y Coordinates of the object’s start point when drawn.

    • If you clicked on the upper left and drew by dragging to the lower right, that would make the start point the upper left corner. 

Expand
titleX Position Definition

The X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image RemovedImage Added

Mid X and Mid Y 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • The Middle Point X and Y Coordinates.

Expand
titleX Position Definition

The X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image RemovedImage Added

End X and End Y 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • The End Point X and Y Coordinates.

Expand
titleX Position Definition

The X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Image RemovedImage Added

Angle 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • This displays the Angle, in degrees, of the Line.

  • The Angle is the space, in degrees, between a given line and an unseen horizontal line intersecting its end point. 

Image RemovedImage Added

Length 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • Displays the Length of the Line in the current dimensions.

Image RemovedImage Added

Bevel Type 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF
Expand
titleBevel Type Definition

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image RemovedImage Added

Layer 

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF
Expand
titleTraced Definition

Tracing the Design provides the Bevel Type and other necessary information to the Vector design in order to either Cut or apply a Non-Blade Tool on the CMC.

The Set Bevels Tab in Trace contains the tools needed to Trace the design.

Image RemovedImage Added